Znaleziono w kategoriach:
Płyty główne (116)
Wróć
DDR5 DIMM_B (64bit, 288-pin module)
DDR5 DIMM_A (64bit, 288-pin module)
SOCKET AM5
CPU_12V
CPU_FAN
AIO_PUMP
CHA_FAN
ATX_PWR
PCIEX16(G5)
ADD GEN2_1
ADD GEN2_2
U10G_234
U10G_C1
LAN_U10G_11
U20G_C6
SATA6G_2
SATA6G_1
EF_FAN
U10G_C10
U5G_89
T_SENSOR
CPU_OV
BATT_CON
M.2(WIFI)
CLR_CMOS
HDMI
USB_16_5
AMD
B850
F_PANEL
USB_1415
CPU
DRAM
VGA
BOOT
2260
2280
MIC_IN
LINE_IN
LINE_OUT
ALED1
SPDIFO
BIOS_FLBK
FLEXKEY
FLBK_LED1 ALED2
ALED3
F_AUDIO
2242
M.2_1(SOCKET3)
VRM_HS_FAN
QUICK START GUIDE
ROG STRIX
B850-I GAMING WIFI
The items labeled below correspond to the installation steps, for steps
and more information on the steps, please refer to the rest of the guide.
ARGB
USB 10Gbps
USB 5Gbps
USB 2.0
Chassis Fan
Front Panel System
Front Panel Audio
Support
SEEKING A SOLUTION?
Scan now for assistance
2
Prepare the components
NOTE: The components listed above are recommendations, please prepare components according to your needs.
Chassis
CPU Memory M.2 SSD
SATA device
Power supply unit Graphics card
CPU Cooler
• Install the Memory
NOTE: Please refer to the manual(s) for more information: Motherboard
Q25171 / First Edition / October 2024
Install key components
• Install the CPU
NOTE: Do not remove the PnP cap before the CPU is properly installed.
Thermal paste
OROR
Please refer to the manual(s) for more information: Motherboard
Please scan for more
information on CPU
installation steps.
3
• Install the M.2 SSD
M.2 Q-Release M.2 Q-Slide
NOTE: Please refer to the manual(s) for more information: Motherboard
OR
Remove
M.2 slot
Remove Optional
M.2 slot
Make sure of the following:
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
Make sure the M.2 Q-Slide clicks and
locks the M.2 SSD
Type-A Install
RemoveType-B
M.2 slot
M.2 slot
Additional Information (on selected models)
• M.2 Q-Latch
clicks and locks
the M.2 SSD
• Secure the
screw properly
• Insert the pin
of the M.2 Anchor
into the hole
4
Install the motherboard into the chassis
For non pre-mounted I/O
shield models only
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis
Install the cooling system
• Air Cooler
• AIO Cooler
AIO_PUMP / W_PUMP
(connect to pump)
CPU_FAN / CPU_OPT
(connect to radiator)
CPU_FAN / CPU_OPT
OR
NOTE: Please refer to these manual(s) for more information: Cooler Chassis
5
Connect cables from Chassis
Ground
+5V Data
ARGB header
Connect to chassis fan and ARGB/RGB headers
B
R
+12V G
RGB header
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis Fan
Chassis fan
Install and connect the power supply unit (PSU)
Make sure the PSU is secured to
the chassis using screws, and that
the chassis has proper airflow
Chassis PSU
NOTE: Input: AC 100~240V, 6A/3A, 50/60Hz
Please refer to the manual(s) for more information:
• Connect the power cables to the motherboard
OROR
Connect cables from PSU
Motherboard PSU
NOTE: Please refer to the manual(s) for more information: