Znaleziono w kategoriach:
EF-M28mm f/3.5 MACRO IS STM
Instructions
ENG
ENG-1
Thank you for purchasing a Canon product.
The Canon EF-M28mm f/3.5 MACRO IS STM
is a macro lens for use on Canon EOS M
Series cameras. It is equipped with an Image
Stabilizer capable of shooting portraits,
scenery and other normal shots, as well as
close-up (macro) shots with a magnication
ratio of 1.2x.
●● “IS” stands for Image Stabilizer.
●● “STM” stands for stepping motor.
Camera Firmware
●● When using this lens, please check the Canon website
for the latest camera rmware. If the camera’s rmware
is not the latest version, be sure to update to the latest
rmware.
●● For details on updating rmware, please check the
Canon website.
Conventions used in this instruction
Warning to prevent lens or camera malfunction
or damage.
Supplementary notes on using the lens and
taking pictures.
ENG-2
Precautions to ensure that the camera is used
safely. Read these precautions thoroughly. Make
sure all details are observed in order to prevent
risks and injury to the user and other people.
Warning Details pertaining to risks that may
result in death or serious injury.
●● Do not look at the sun or a bright light source
through the lens. Doing so could result in vision loss
or blindness.
●● Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a re.
Caution Details pertaining to risks that may
result in injury.
●● Do not hold the Macro Lites located on the front
of the lens close to the eyes or stare at them when
they are illuminated. Doing so may result in eye
damage.
●● Do not leave the camera in locations subject to
high or low temperatures. This may result in the
camera becoming excessively hot or cold, which may
cause burns or other injuries when touched.
Caution Details pertaining to risks that may
result in damage to property.
●● Do not leave the lens in excessive heat such as in a
car in direct sunlight. High temperatures can cause the
lens to malfunction.
Safety Precautions
ENG-3
General Precautions
Handling Precautions
●● If the lens is taken from a cold environment into a
warm one, condensation may develop on the lens
surface and internal parts. To prevent condensation in
this case, rst put the lens into an airtight plastic bag
before taking it from a cold to warm environment. Then
take out the lens after it has warmed gradually. Do the
same when taking the lens from a warm environment
into a cold one.
●● Please also read any lens related handling precautions
listed in your camera’s instruction manual.
Shooting Precautions
●● Note that there are cases in which the white ring on
the front of the lens may be reected into photographs
if the lens is held close to reective objects (glass
surface on wristwatches, for example), even if the
Macro Lites are not illuminated. This can be avoided by
attaching the hood when taking photographs.
ENG-4
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Do not make any changes or modications to the equipment
unless otherwise specied in the instructions. If such
changes or modications should be made, you could be
required to stop operation of the equipment.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
CAN ICES-3 (B) / NMB-3 (B)