Znaleziono w kategoriach:
●❶
●❷
●❸
Thank you for purchasing a Canon product.
EF35mm f/1.4L II USM is a large-diameter wide-angle lens for EOS cameras.
● “USM” stands for Ultrasonic Motor.
Safety Precautions
● Do not look at the sun or a bright light source through the lens or
camera. Doing so could result in loss of vision.
Looking at the sun directly through the lens is especially hazardous.
● Whether it is attached to the camera or not, do not leave the lens under
the sun without the lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a fire.
Handling Cautions
● If the lens is taken from a cold environment into a warm one,
condensation may develop on the lens surface and internal parts. To
prevent condensation in this case, first put the lens into an airtight plastic
bag before taking it from a cold to warm environment. Then take out the lens
after it has warmed gradually. Do the same when taking the lens from a warm
environment into a cold one.
● Do not leave the lens in excessive heat such as in a car in direct sunlight.
High temperatures can cause the lens to malfunction.
Usage Precautions
● When using this lens, please check the Canon website for the latest camera
firmware. If the camera’s firmware is not the latest version, be sure to update
to the latest firmware.
● For details on updating firmware, please check the Canon website.
Conventions used in this instruction
Warning to prevent lens or camera malfunction or damage.
Supplementary notes on using the lens and taking pictures.
1. Mounting and Detaching the Lens
See your camera’s instructions for details on mounting and detaching the
lens.
● After detaching the lens, place the lens with the rear end up to prevent
the lens surface and contacts from getting scratched.
● If the contacts get soiled, scratched, or have fingerprints on them,
corrosion or faulty connections can result. The camera and lens may not
operate properly.
● If the contacts get soiled or have fingerprints on them, clean them with a
soft cloth.
● If you remove the lens, cover it with the lens cap and dust cap. To attach
the dust cap properly, align the lens mount index and the ○ index of the
dust cap, and turn clockwise ❶. To remove it, reverse the order.
● The lens mount has a rubber ring for enhanced dust- and water-
resistance. The rubber ring may cause slight abrasions around the
camera’s lens mount, but this will not cause any problems. If the rubber
ring becomes worn, it is replaceable by a Canon Service Center at cost.
2. Setting the Focus Mode
To shoot in autofocus (AF) mode, set the focus mode switch to AF ❷.
To shoot in manual focus (MF) mode, set the focus mode switch to MF, and turn
the focusing ring to set the focus ❸.
The focusing ring always works, regardless of the focus mode.
When the camera AF mode is ONE SHOT AF, focus manually by pressing
the shutter button halfway and turning the focusing ring. (Full-time manual
focus)
Nomenclature
●① Focusing ring
●② Hood mount
●③ Filter mounting thread
●④ Distance scale
●⑤ Rubber ring
●⑥ Focus mode switch
●⑦ Lens mount index
●⑧ Contacts
EF Lenses
EF35mm f/1.4L II USM
Instructions
CT1-8605-000 1504SZ © CANON INC. 2015
●❺
●
●❻
●❹
3. Infinity Compensation Mark
To compensate for shifting of the infinity focus point that results from changes in
temperature. The infinity position at normal temperature is the point at which the
vertical line of the distance scale L mark is aligned with the distance index ❹.
For accurate manual focusing of subjects at infinity, look through the
viewfinder or look at the magnified image* on the LCD screen while
rotating the focusing ring.
* For cameras with Live View shooting capability.
4. Depth-of-Field Scale
The depth of field is the distance in front of and behind the plane of focus on the
subject that appears sharp. The depth of field is indicated by the area between
the depth-of-field scale lines below the distance scale.
The depth-of-field scale is an approximate indicator.
5. Hood
The EW-77B hood can keep unwanted light out of the lens, and also protects the
lens from rain, snow, and dust.
To attach the hood, align the hood’s attachment position mark with the red dot
on the front of the lens, then turn the hood in the direction of the arrow until the
lens’s red dot is aligned with the hood’s stop position mark ❺.
To remove the hood, hold down the button on the side and turn the hood in the
direction of the arrow until the position mark on the hood aligns with the red dot ❻.
The hood can be reverse-mounted on the lens for storage.
● Part of the picture may be blocked if the hood is not attached properly.
● When attaching or detaching the hood, grasp the base of the hood to
turn it. To prevent deformation, do not grasp the rim of the hood to turn
it.
6. Filters (Sold Separately)
You can attach filters to the filter mounting thread (ø72 mm) on the front of the
lens.
● Only one filter may be attached.
● Use the Canon Circular Polarizing Filter PL-C B (ø72mm) as the
polarizing filter.
● To adjust the polarizing filter, first remove the lens hood.
7. Extension Tubes (Sold Separately)
You can attach extension tube EF12 II or EF25 II for magnified shots. For
shooting distance and magnification, see the extension tube specifications.
MF mode is recommended for accurate focusing.
8. Close-up Lenses (Sold Separately)
Attaching a close-up lens 500D (72 mm) enables close-up photography.
Magnification is from 0.07 to 0.27 times.
● Close-up lens 250D cannot be attached because there is no size that
fits the lens.
● MF mode is recommended for accurate focusing.
● The lens length is measured from the mount surface to the front end of the
lens. Add 24.2 mm when including the lens cap and dust cap.
● The size and weight listed are for the lens only, except as indicated.
● The extenders cannot be used with this lens.
● All data listed is measured according to Canon standards.
● Product specifications and appearance are subject to change without notice.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Do not make any changes or modifications to the equipment unless otherwise
specified in the instructions. If such changes or modifications should be made,
you could be required to stop operation of the equipment.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich
the receiver is connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
CAN ICES-3(B)/NMB-3(B)
Specifications * Sold Separately
Angle of view Lens
construction Minimum
aperture Max.
magnification Min. focusing
distance Filter diameter Max. diameter and length Weight (Approx.) Hood Lens Cap Case*
Diagonal Vertical Horizontal
EF35mm f/1.4L II USM 63° 38° 54° 11-14 22 0.21x 0.28m/0.92ft 72mm 80.4x105.5mm
(3.2”x4.2”) 760g/26.8oz. EW-77B E-72 II LP1219
Extension Tube Specifications
(Sold Separately) Magnification
(X)
Focusing Distance Range
(mm) (inch)
EF35mm f/1.4L II USM EF12 II 0.58-0.36 194-229 (7.6-9.0)
EF25 II 1.03-0.8 184-192 (7.2-7.6)
Button
Infinity compensation mark
Distance index
Depth-of-field scale