Znaleziono w kategoriach:
ENG EF-M LENS Instructions
EF-M11-22mm f/4-5.6 IS STM
①
②
③
④⑤
⑥
⑦
⑩
⑨
⑧
Nomenclature
① Focusing ring
② Hood mount
③ Filter Mounting Thread
④ Lens mount index
⑤ Contacts
⑥ Zoom position index
⑦ Lens retracted position index
⑧ Zoom ring
⑨
Focal length indicator
⑩
Lens-retraction switch
Thank you for purchasing a Canon product.
The Canon EF-M11-22mm f/4-5.6 IS STM is a 2x wide-
angle zoom lens developed for interchangeable-lens digital
cameras compatible with EF-M lenses*.
*
Only the following cameras are compatible with EF-M lenses (as
of June 2013)
:
EOS M
When attaching this lens to a Canon EOS M camera with
firmware earlier than version 2.0.0, there is a slight chance
that the camera will not operate properly during shooting.
Therefore, please be sure to update the EOS M firmware to
version 2.0.0 or later (For information about updating your
camera’s firmware, please check the Canon website).
• "IS" stands for Image Stabilizer.
• "STM" stands for stepping motor.
Safety Precautions
• Do not look at the sun or a bright light source through
the lens. Doing so could result in vision loss or blindness.
• Whether it is attached to the camera or not, do not
leave the lens under the sun without the lens cap
attached. This is to prevent the lens from concentrating the
sun’s rays, which could cause a fire.
Handling Cautions
• If the lens is taken from a cold environment into a warm
one, condensation may develop on the lens surface
and internal parts. To prevent condensation in this case,
first put the lens into an airtight plastic bag before taking it
from a cold to warm environment. Then take out the lens
after it has warmed gradually. Do the same when taking the
lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in a car in direct
sunlight. High temperatures can cause the lens to malfunction.
• Please also refer to the handling cautions found in your
camera’s instructions.
Conventions used in this instruction
Warning to prevent lens or camera malfunction or
damage.
Supplementary notes on using the lens and taking
pictures.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes
or modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-
003.
1. Mounting and Detaching the Lens
See your camera’s instructions for details on mounting and
detaching the lens.
• After detaching the lens, place the lens with the rear end
up to prevent the lens surface and contacts from getting
scratched. (fig.❶)
• If the contacts get soiled, scratched, or have fingerprints
on them, corrosion or faulty connections can result. The
camera and lens may not operate properly.
• If the contacts get soiled or have fingerprints on them, clean
them with a soft cloth.
• If you remove the lens, cover it with the dust cap. To
attach it properly, align the lens mount index and the
index of the dust cap as shown in the diagram, and turn
clockwise. (fig.❷) To remove it, reverse the order.
2. Shooting Preparations and Retracting Lens
Shooting Preparations: (Set the lens to the shooting
position)
Align the lens retract position index and zoom position index.
Maintain pressure on the lens-retraction switch in the [▲]
direction. Slightly rotate the zoom ring in the direction of the
white arrow to release the lens-retraction switch and rotate
further until it clicks. The lens now ready for shooting. (The no.
11 pointing line in the focal length indicator which shows above
or to the left of the zoom position index extension line.) (fig.❸)
Retracting Lens:
Maintain pressure on the lens-retraction switch in the [▲]
direction. Rotate the zoom ring in the opposite direction to the
white arrow. Align the lens retract position index and the zoom
position index. Release the lens-retraction switch to retract the
lens.
Do not forcibly rotate the zoom ring if its movement
becomes constricted at the retractable end or the wide
end, as there is a danger of damaging the lens-retraction
switch mechanism.
3. Zooming
Turn the lens’ zoom ring to adjust the size of the photo field or
subject. (fig.❹)
• For wide shots, turn the zoom ring toward the wide end.
• For close-ups, turn the zoom ring toward the telephoto end.
• Be sure to finish zooming before focusing. Zooming after
focusing can affect the focus.
• Blurring may temporarily occur if the zoom ring is quickly
rotated.
• Zooming during still image exposure will result in delayed
focus. This causes any streaks of light that are captured
during exposure to be blurred.
Wide end
Telephoto end
Zoom ring
❹
❸
❷
❶
ENG-1
CT1-8587-001
COPY
❺
❻
4. Manual Focus
When the camera’s focus mode is set to [MF], focus manually
by turning the focusing ring. (fig.❺)
Quickly rotating the focusing ring may result in delayed
focus.
• Focus mode is set using the camera. Please refer to the
camera’s instructions.
• After autofocusing in [AF+MF] mode, focus manually
by pressing the shutter button halfway and turning the
focusing ring (full-time manual focusing).
5. Image Stabilizer
This lens is equipped with an Image Stabilizer. This function
corrects camera shake, allowing users to capture sharp
images. Also, the Image Stabilizer automatically provides
optimal image stabilization depending on shooting conditions
(such as shooting still subjects and following shots). Please set
the Image Stabilizer ON or OFF using the camera settings. See
your camera’s instructions for details.
• The Image Stabilizer cannot compensate for a blurred
shot caused by a subject that moved.
• The Image Stabilizer may not be fully effective if
you shoot from a violently shaking vehicle or other
transportation.
• The Image Stabilizer consumes more power than normal
shooting, so fewer shots can be taken if you use the
function.
• When shooting a still subject, it compensates for camera
shake in all directions.
• It compensates for vertical camera shake during following
shots in a horizontal direction, and compensates for
horizontal camera shake during following shots in a
vertical direction.
• When you use a tripod, the Image Stabilizer should be
turned off to save battery power.
• Even with a monopod, the Image Stabilizer will be as
effective as during hand-held shooting.
However, depending on the shooting environment, the
Image Stabilizer effect may be less effective.
■ Dynamic IS Function (Movie shooting only)
The EF-M11-22mm f/4-5.6 IS STM is equipped with dynamic
IS, effective when shooting while walking since it expands the
IS range.
• Achieves effective IS at the wide end.
• Automatically activates when the camera is set to Movie
Shooting.
6. Hood (sold separately)
The EW-60E hood cuts out unwanted light and protects the
front of the lens from rain, snow, and dust.
To attach the hood, align the hood’s attachment position mark
with the red dot on the front of the lens, then turn the hood as
shown by the arrow until the lens’ red dot is aligned with the
hood’s stop position mark. (fig.❻)
The hood can be reverse-mounted on the lens for storage.
• If the hood is not attached properly, vignetting (darkening
of the perimeter of the picture) may occur.
• When attaching or detaching the hood, grasp the base of
the hood to turn it. To prevent deformation, do not grasp
the rim of the hood to turn it.
7. Filters (sold separately)
You can attach filters to the filter mounting thread on the front
of the lens.
Only one filter may be attached.
0613Ni © CANON INC. 2013 ENG-2
Specifications
Focal Length/Aperture 11-22mm f/4-5.6
Lens Construction 9 groups, 12 elements
Minimum Aperture f/22-32
Angle of View
Diagonal: 102°10'-63°30'
Vertical: 68°55'-37°50'
Horizontal: 91°50'-54°30'
Min. Focusing Distance 0.15 m/0.49 ft.
Max. Magnification 0.3x (at 22 mm)
Field of View
Approx. 103x155-50x74 mm/
4.06x6.10-1.97x2.91 inch
(at 0.15 m/0.49 ft.)
Filter Diameter 55 mm
Max. Diameter and Length
(When the lens is retracted) 60.9x58.2 mm/2.40x2.30 inch
Weight Approx. 220 g/7.8 oz
Hood EW-60E (Sold Separately)
Lens Cap E-55
Dust Cap Lens Dust Cap EB
Case LP814 (Sold Separately)
• Equivalent to 18-35 mm in the 35mm film format.
• The lens length is measured from the mount surface to the
front end of the lens. Add 20.2 mm when including the lens
cap and dust cap.
• The size and weight listed are for the lens only, except as
indicated.
• Extenders cannot be used with this lens.
• Aperture settings are specified on the camera. The camera
automatically compensates for variations in the aperture
setting when the camera is zoomed in or out.
• All data listed is measured according to Canon standards.
• Product specifications and appearance are subject to change
without notice.
COPY