Znaleziono w kategoriach:
A
Surface Selection
Find a flat spot on the headphones for the 0.5 inch/12.7mm circle of adhesive. The adhesive will stick to smooth and
mesh surfaces but does not stick well to porous, lacquered, or rubberized surfaces.
1. Put the headphones on to ensure the ModMic will reach the corner of your mouth from the desired mounting point.
2. Thoroughly clean and dry the surface with the included alcohol pad.
Attaching & Orientation
1. Attach a to the that holds the ModMic’s boom.
2. Remove the protective backing from the adhesive.
3. While holding the orient the mic boom angle down so
it points towards where your mouth will be when using your
headphones. (This will reduce the need for additional bends
in the boom after installation—see Figure A).
4. Press the whole mic/clasp down onto the cleaned spot and
hold firmly for 60 seconds . Allow the adhesive to cure
for 1 hour .
ModMic USB 2 Installation
Parts List
One
ModMic USB 2 Two base clasps, one
top clasp with cap &
extra 3M adhesives
One foam
pop filter
In-line
mute switch
5x
cable clips
One alcohol
wipe
Carrying case &
instruction manual
A to C
adapter
5x
Getting the most from your ModMic USB 2
1. The mic is sensitive to plosive blast/wind
from your mouth, especially “P” sounds
(see Figure C).
2. To lessen unwanted cable torque on the clasp,
fold the cable end of the boom so that it is
close to the clasp (see Figure D).
3. Ensure the mic symbol on the boom is pointed
towards your mouth (see Figure E for detail).
Do you need a little more help?
Here are some common troubleshooting steps that may help you out.
1. Ensure the mute switch is unmuted. A red light means the mic is muted. Press the button one time to mute/unmute.
2. Make sure you have the ModMic selected as your default listening device in your recording devices options.
3. Try multiple ports on your computer/device if you’re having audio quality issues.
4. Test the device on another port, or machine/device if possible.
5. If you need additional help contact us at CustomerService@AntlionAudio.com for service.
D
C
B
L R
5. To reverse the orientation of the boom from the left
earcup to the right, do not remove the boom’s screw-on
clasp. Simply re-bend the cable end of the boom
downward in the opposite shape (see Figure B).
Always ensure the cable is pointing downward to
prevent cable breaks.
E
Microphone Icon
ModMic USB 2 Warranty
FROM DATE OF PURCHASE, OUR TWO (2) YEAR LIMITED
WARRANTY COVERS MANUFACTURING DEFECTS OF THE
MODMIC AND/OR ITS ACCESSORIES.
If you experience a product defect and are within the return period of the
reseller from which you purchased, please return the item to the retailer.
If you are outside their return window but within our warranty window
of 2 years (or the minimum warranty required by your country from date
of purchase), we will repair or replace your ModMic for any manufacturing
defects in the ModMic and/or its accessories at our discretion.
Our Warranty does not cover/is voided by the following:
1. Damage caused by accident, abuse, neglect, or misuse.
2. If you cannot supply a valid dated proof of purchase.
3. If the ModMic has been disassembled or modified without
instruction from Antlion Audio staff.
4. Warranties are non-transferable and apply only to the original owner.
We require you to send your defective product back to
us for repair/replacement. Before returning your ModMic
for repair or replacement please contact us first at
CustomerService@AntlionAudio.com for further assistance!
After Warranty repair or replacement, your Warranty will remain in
effect until either two (2) years after your original purchase date,
or ninety (90) days after repair or replacement, whichever is longer.
For Australia Only:
Our goods come with guarantees
that cannot be excluded under the
Australian Consumer Law. You are
entitled to a replacement or refund for
a major failure and for compensation
for any other reasonably foreseeable
loss or damage. You are also entitled
to have the goods repaired or replaced
if the goods fail to be of accessible
quality and the failure does not
amount to a major failure.
EU Responsible Person Contact:
Sea&Mew Consulting GmbH
C/O Yuan Li
Mittenhuber Straße 4
Neumarkt, 92318
Germany
Compliance.EU@outlook.com
+4915224685061
Antlion Audio, P.O. Box 86339, Portland, OR 97286, USA. Telephone: +01 (971) 319-0326
www.AntlionAudio.com TikTok: @antlionaudio Instagram: @antlionaudio
For more information/extra clasps/questions/feedback visit www.AntlionAudio.com. Designed in Portland, Oregon.
Manufactured in China. ModMic and Antlion logo are registered trademarks of GTDevice LLC. U.S. and International patents.
Questions? Suggestions?
Join our Discord!
Fijación y orientación
1. Adhiera un al que sostiene el brazo del ModMic.
2. Retire el reverso protector del adhesivo.
3. Mientras mantiene presionado el botón oriente el ángulo
del brazo del micrófono hacia abajo para que apunte hacia
donde estará su boca cuando use sus auriculares. (Esto
reducirá la necesidad de curvas adicionales en el brazo
después de la instalación: ver Figura A).
4. Presione todo el micrófono/cierre hacia abajo en el lugar
limpio y manténgalo firmemente presionado durante 60
segundos . Deje que el adhesivo se cure durante 1 hora .
Lista de piezas
Un ModMic
USB 2 Dos cierres de base, un
cierre superior con tapa y
adhesivos 3M adicionales
Un filtro pop
de espuma
Interruptor de
silencio en línea
5x pinzas
para cables
Una toallita
con alcohol
Estuche de
transporte y manual
de instrucciones
Adaptador
de A a C
5x
A
Selección de superficie
Encuentre un punto plano en los auriculares para el círculo de adhesivo de 12.7 mm/0.5 pulgadas. El adhesivo se adhiere a
superficies lisas y de malla, pero no se adhiere bien a superficies porosas, lacadas o engomadas.
1. Póngase los auriculares para asegurarse de que el ModMic llegue a la comisura de la boca desde el punto de montaje deseado.
2. Limpie y seque a fondo la superficie con la almohadilla con alcohol incluida.
Instalación de ModMic USB 2