3
3
EN – USER MANUAL
BOX CONTENTS
−TrueLife AquaFloss Compact C200
− 1× Standard nozzle heads, 1× Dental
Plaque nozzle head, 1× Orthodontic
nozzle head, 1× Periodontal nozzle head
−USB charging cable
−Manual and safety instructions
PRODUCT DESCRIPTION
1. Nozzle head
2. Button to release nozzle head
3. On/O button
4. Display
5. Mode change button
6. Handle
7. Water tank
8. Water tank cap
9. Charging Cable
Warning: There may be residual water
in the device. This is distilled water used
during quality control testing.
SOFT
MEDIUM
STRONG
PULSE
DIY
1
3
4
2
6
8
5
7
9
4
INSTRUCTIONS FOR USE
Before the rst use, remove all packaging material.
If the water osser has been stored in a low temperature environment during trans-
port, leave it at room temperature for at least two hours before use.
1. Connect the head to the shower. A click indicates correct insertion. You can choo-
se from the following headers:
− Standard Head – For daily plaque removal from interdental spaces and along
gum lines
−Periodontal Head – For cleaning periodontal pockets using a rubber tip
− Orthodontic head – For removing plaque from brackets and wires of braces
and other hard-to-reach places
− Dental Plaque Head – For more eective removal of plaque around implants,
crowns and bridges.
2. Remove the water tank cap and ll the tank with water; the temperature of the
water should not exceed 40 °C. The capacity of the water tank is 300 ml. Then
replace the cap, ensuring that water does not spill.
3. Press the „mode change“ button and select the desired ossing mode. The mode
you have just selected will be shown on the display. You can also change the mode
while ossing. You can choose between 4 modes:
− Soft mode – suitable for people with sensitive teeth and for people starting
out with oral shower. Pressure range: 20–50 PSI
− Medium mode – suitable for everyday brushing. Pressure range: 50–80 PSI
−Strong mode – suitable for deep cleaning. Pressure range: 70–110 PSI
− Pulse mode – suitable for massaging teeth and gums. Pressure range:
70–110 PSI
− DIY mode – adjust the pressure to suit your needs. Long press the mode
change button to enter DIY mode. A scale will appear on the display and
gradually go from minimum pressure to maximum pressure. Press the mode
change button again to select the water pressure as required. Pressure range:
8–110 PSI
4. Leave your mouth slightly open to allow water to rinse from your mouth into the
sink. Press the On / O button to start the osser. Direct the water jet at a 90° angle
to the teeth and gums. Slowly run the stream of water around your teeth. Direct
the stream of water onto the gums and into the space between the teeth. If you
have braces, you can direct the water between the joints of the braces.
5. When you have nished ossing, switch o the device using the On / O button.
Open the water tank cap and pour out any remaining water. Switch the device on
again with the On / O button to drain the water from the pump. Press the On /
O button to turn o the device and close the water tank cap.
Warning: To prevent the build-up of bacteria, ensure that no water remains in the device.
If you do not intend to use the device for a longer time, make sure that it is thoroughly
dried before storing it.
5
CHARGING
The water osser is not supplied with a fully charged battery. Before using for the
rst time, fully charge the water osser.
Plug one end of the USB cable into the charging socket at the rear of the water o-
sser. Plug the other end of the USB cable into an adapter (adapter not included).
Insert the adapter into the plug socket.
It takes approximately 4 hours to fully charge the water osser.
Note: To ensure maximum battery life, we recommend charging the water osser once
a week.
INSERTING AND REPLACE THE NOZZLE HEAD
Insert the nozzle head into the hole at the top of the water osser. You will hear a
click when the nozzle head has been correctly attached.
To remove the nozzle head from the main body, press and hold the release button
and then detach the nozzle head from the water osser.
The nozzle head rotates 360 °.
Warning: Only insert and remove the nozzle head when the water osser is switched o.
Note: Nozzle heads are items of personal hygiene and are not covered by warranty.
MAINTENANCE
Use only water and neutral detergents to clean the device. Never use caustic or
abrasive cleaners as they may damage the device. Do not use water whose tem-
perature exceeds 50 °C. Keep the device away from high temperatures and avoid
direct sunlight.
1. The device
Remove dirt by wiping with a towel or cloth with liquid soap and water, then ensure
all water is rinsed o and wipe dry.
Do not immerse the device in water.
Warning: Water must not enter the USB socket.
2. Water tank
Wash the tank with water and wipe with a dry cloth.
Dry the tank thoroughly if you do not intend to use it for a longer time.
Note: For greater ease of cleaning, the water tank can be removed from the body of the
water osser.
3. Nozzle head
Wash the nozzle head with water and wipe with a cloth.