3
3
EN – USER MANUAL
BOX CONTENTS
−TrueLife AquaFloss Station S600
− 3× Standard nozzle, 1× Dental Plaque
nozzle, 1× Orthodontic nozzle,
1× Periodontal nozzle
−Manual and safety instructions
PRODUCT DESCRIPTION
9
8
7
6
5
4
3
2
1
1. Nozzle storage compartment
2. Water reservoir
3. Control knob
4. Rubber suction cups
5. Storage compartment lid
6. Swivel attachment
7. Nozzle release button
8. Power button
9. Base
4
Nozzles
Please note: There may be
residual water in the device.
This is distilled water that is
used when testing the device.
INSTRUCTIONS FOR USE
Remove all packaging materials before rst use.
If the water osser has been exposed to a low temperature environment during
transport, leave it at room temperature for at least two hours before use.
1. Connect the nozzle to the handle. It will click when correctly inserted.
2. Remove the water reservoir from the base and ll it with water not exceeding
40 C. The capacity of the reservoir is 600 ml. Return the reservoir to the base and
make sure that no water overows.
3. Plug in the water osser.
4. Turn the control knob to turn on the device. Turn the knob again to adjust to the
desired pressure intensity.
5. Lean over the sink and put the nozzle in your mouth. Point the nozzle at your teeth
and use the power button to start cleaning.
6. Leave your mouth slightly open to allow water to ow freely from your mouth
into the sink. Direct the water stream at a 90° angle towards the teeth and gums.
Slowly move the water stream around the teeth. Direct the water stream towards
the gums and the spaces between the teeth. If you have braces, you can direct the
water between the joints of the braces.
7. If you want to pause cleaning, use the power button on the handle.
8. After cleaning, switch o the device using the control knob. Open the lid of the
water tank and pour out the remaining water. Switch the device on again to
empty the water from the pump.
Note: To prevent the spread of bacteria, make sure that no water is left in the device. If
you are not going to use the device for a long period of time, make sure it is thoroughly
dried before storing it.
INSERTING/REPLACING THE NOZZLE
Insert the nozzle into the opening at the top of the osser. When correctly inserted
you’ll hear a click.
Standard Periodontal Dental Plaque Orthodontic
5
To remove the nozzle from the handle, press and hold the nozzle release button and
pull the nozzle out.
The nozzles can be swivelled 360°.
The box includes the following nozzles:
− Standard Jet – used to rinse hard-to-reach areas and places where a conven-
tional toothbrush cannot reach.
− Orthodontic Jet – a special orthodontic nozzle designed to clean and rinse
hard-to-reach areas around braces.
− Periodontal Jet – directs the stream of water or mouthwash below the gum
line thanks to the tapered silicone end.
− Dental Plaque Jet – used for more eective removal of dental plaque with
easier access to aected areas.
Note: Only insert and remove the nozzles when the osser is switched o.
Note: Nozzles are subject to personal hygiene and are not subject to warranty.
MAINTENANCE
Use only water and neutral detergents for maintenance purposes. Never use caus-
tic or abrasive cleaners as they can damage the equipment. Do not use water at
temperatures above 50 °C. Keep the equipment away from high temperatures and
avoid direct sunlight.
1. Base
Remove dirt by wiping it down with a towel or cloth with liquid soap and water. Then
wipe it dry. Do not immerse the device in water.
2. Water reservoir
Wash the reservoir with water and wipe with a dry cloth.
Dry the reservoir thoroughly if you are not going to use it for a long time.
After using a special product in the reservoir (mouthwash), rinse the reservoir each
time. Partially ll the reservoir with clean warm water, direct the nozzle into the sink,
turn on and let it ow until the reservoir is completely empty. Regular ushing pre-
vents clogging and prolongs the life of the product.
3. Nozzles
Wash the nozzle with water and wipe with a cloth.