Znaleziono w kategoriach:
Foteliki samochodowe (10)
Wróć
©2013 Graco GIM-0004A 07/13
Owner’s Manual
Parts list
Fitting Guide
Endure Group 123 (9-36kg)
9-18kg 15-36kg
2
1
2
3
4
5
6
7
9
10
11
12
12
13
14
8
1
Headrest
2
Slot
3
Backrest
4
Harness
5
Chest pad
6
Armrest
7
Buckle & crotch pad
8 Newborn liner
9
Harness adjuster strap
10
Belt guide
11
Button
(headrest height adjustment)
12
Harness strap
13
Harness connector
14
Pocket for instruction manual
Assembling your
Endure 123 Child
Restraint.
Once removed
from the box,
place your new
Endure123 on the
floor as shown in
Diagram 1, left.
Open the two parts
out so that the
backrest and seat
lie flat, as shown in
Diagram 2.
Locate the two
hooks at the base
of the backrest
over the bars on
the back of the seat
base (inset).
Raise the backrest
to the vertical
postion until it
snaps into place.
Diagram 3
1
2
3
3
IMPORTANT NOTE
Children should not be left in their child restraint system
unattended.
Any luggage or other objects liable to cause injuries in
the event of a collision must be properly secured.
This child restraint must not be used without the cover.
The seat cover should not be replaced with any other
than the one recommended by the manufacturer,
because the cover constitutes an integral part of the
restraint performance.
The child restraint should be changed when it has been
subject to violent stresses in an accident.
It is dangerous to make any alterations or additions to
the child restraint without the approval of the competent
authority.
Please always fasten the child restraint when it is inside the
vehicle.
It is dangerous to not follow closely the installation
instructions provided by the child restraint manufacturer.
Any straps holding the child restraint to the vehicle should
be tight.
Only use contact points and connections described in
the instructions and marked on the child restraint.
Care and maintenance
THESE INSTRUCTIONS ARE
IMPORTANT. PLEASE READ
CAREFULLY AND RETAIN FOR
FUTURE REFERENCE.
It is dangerous to NOT follow the
instructions for this product.
Backrest cover removal
First release the elastic strap at the
bottom of the backrest cover. Slide
the cover off. The cover can now be
cleaned.
Headrest and Seat cushion cover
removal
Slide the cover off. The cover can
now be cleaned.
Washing the covers
Machine wash cover in cold water
on delicate cycle and drip-dry.
DO NOT USE BLEACH.
1 This is a “Universal” child restraint. It is
approved to ECE Regulation 44.04 for
general use in vehicles and will fit most,
but not all vehicle seats.
2 Only suitable for use with 3 point
retractor vehicle safety belts approved
to ECE regulation 16 or equivalent
standards.
3 A correct fit is likely if the vehicle
manufacturer has declared in the
vehicle handbook that the vehicle is
capable of accepting a “Universal” child
restraint of this group.
4 This child restraint has been declared
“Universal: under more stringent
conditions than those applied to earlier
designs which do not carry this notice.
5 If in any doubt, consult either the child
restraint manufacturer or the retailer.
4
Use the Correct Shoulder
Strap Height
Please always read the manual
before using it. The manual is
located in the pocket at the side
of the seat.
TOO LOW
TOO HIGH
CORRECT
5
1
Top slot
2
Middle slot
3
Bottom slot
4
Top loop
5
Bottom loop
Using the Correct Strap
Positioning
1 For infants and toddlers
(9kg to 18kg) use middle
2
and bottom
3
slots and the
top
4
loops on the harness
strap.
2 For older children (up to
18kg) use the top
1
and
middle
2
slots and the
bottom
5
loops on the
harness strap.
1
2
1
2
3
4
5