Znaleziono w kategoriach:
Szafa RACK LANBERG 19" 27U FF01-6627-12BL 600 x 600 mm, Stojąca Czarny

Instrukcja obsługi Szafa RACK LANBERG 19" 27U FF01-6627-12BL 600 x 600 mm, Stojąca Czarny

Powrót
Users manual
Instrukcja obsługi
19” Rack cabinets
FF01 15U,22U,27U,32U,37U,42U, 600*600, 600*800 series
Szafy stojące 19”
seria FF01 15U,22U,27U,32U,37U,42U, 600*600, 600*800
2021/08
Lanberg © 2015-2021
2EN
1. Important introductory recommendations and usage information
1.1 Introduction
Manual also contains logistic and technical data, instructions, and regulations that must be observed and complied with during
transport, assembly, use, and potential maintenance of the products. Under no circumstances should you use the device before
carefully reading and fully adapting to all information in the user’s manual. Keep this manual for future reference. All photos, illustrations
contained in the instructions are for reference only. The information contained in this manual has been veried and is considered
sucient. The supplier is not responsible for any inaccuracies that may be included in this document, nor is he responsible for updating
or keeping the current information in this manual, nor for notifying its users or organization about the updates. In particular, Lanberg
owners are not responsible for any equipment, software, or data stored/used with the product, including maintenance, replacement,
integration, installation, or recovery of hardware, software, or data in the event of misuse of the product or its components.
Lanberg brand owners reserve the right to make changes to this manual at any time without notice. The products mentioned in this
manual, including the documentation, are the property of the Lanberg brand owners and its licensors. Any use or reproduction of
these products, including documentation, is prohibited, except as expressly authorized under the appropriate license terms.
NOTE: For the most up-to-date version of this manual, please visit our website at www.lanberg.eu.
1.2 Compliance with legal and regulatory provisions regarding safety and the environment
This product complies with EU safety and environmental regulations.
The products listed in the following instructions have been approved for trading within the EU, by obtaining a European Union
Declaration of Conformity, which contains a declaration with the essential requirements and other relevant provisions of the following
Directives, and that the following harmonized standards have been applied.
Directive: RoHS 2011/65/UE + 2015/863/UE
Standards: IEC 62321-4:2013 + A1:2017; IEC 62321-5:2013;
IEC 62321-6:2015; IEC 62321-7-2:2017; IEC 62321-8:2017;
With the development of products and updates to CE regulations, the declaration may change. The latest declaration of conformity
(CE) can be found at: www.lanberg.eu.
NOTE: The use of the WEEE symbol (crossed-out wheelie bin symbol) means that this product cannot be treated as household waste.
Proper disposal of used equipment avoids risks to human health and the environment, resulting from the possible presence of
hazardous substances, mixtures, and components in the equipment, as well as improper storage and processing of such equipment.
The selective collection also allows you to recover materials and components, from which the device was manufactured. For more
information about the recycling of this product, please contact the retail outlet, where the product was purchased, or request
information from the local authority.
1.3 General safety precautions
The device specications must be strictly observed when using the product and connecting it to any external products. The
specications of the external devices to which this device is to be connected must also be observed.
The product cannot be used outside of the rated values in its specication. The warranty does not cover any damage caused by
adeviation from these values when using the device.
All installations, connections, cabling, and circuits in which the product will be used must be made in a manner consistent with
locally applicable electricity regulations and in such a way as to eliminate the risk of people walking or tripping over them. Use
only power cables with VDE and CE certication when connecting them to the device. It is necessary to use the same procedures
mentioned in this section when connecting the cabling to the product or to the external components.
For external devices connected to this product, the operating instructions supplied by their manufacturer must be strictly observed.
To ensure safety and compliance of the device, use only components or parts that meet the specications or are recommended by
the manufacturer.
During the warranty period, it is forbidden to replace any elements of the product by its users. Maintenance should be entrusted
only to qualied technical personnel, such as the manufacturer’s technical department or an authorized importer.
If it is necessary to perform maintenance of the device, it should be carried out or supervised by a person having appropriate
qualications and technical knowledge about the device, while maintaining proper precautions. All this under the local regulations
in force.
If it is necessary to perform maintenance of the equipment or similar activities that will require opening the device or contact with
elements that may be under potential voltage, the following safety rules should be observed before carrying out these activities:
remove all bracelets, necklaces, rings, watches or other metal hand and neck objects and use tools with insulated handles.
Always before performing the equipment maintenance, there should be a person nearby who would react and take appropriate
steps to assist the person in charge of the device maintenance in the event of an accident. A person undertaking the maintenance
should always wash hands after nishing his / her work.
NEVER allow a situation where sparks or ames could occur near the device. The aftermath of such a situation could have very
negative consequences for people and things in the vicinity.
In the event of a re, immediately and (without unnecessary delay) disconnect the power supply and notify the re department of
the situation by dialing their assigned emergency number in the country of your stay.
The product is intended for indoor use. Do not rebuild and/or modify the products and/or their components.
Under no circumstances, other external products are to be introduced (connected to the device), that are non-compliant with the
Lanberg © 2015-2021 3
EN
intended use of that device and/or not intended for that purpose.
The manufacturer and distributor are not responsible for any damages resulting from improper use and improper handling of the
product (not in accordance with this manual).
Before attempting to attach or disconnect a device, connect or disconnect cables to it in a 19” wall-mount cabinet, please rstly
connect all components to a veried and ecient grounding.
Make sure that all parts assembled from the beginning in 19” wall-mount cabinet, as well as equipment assembled by the user, are
properly screwed or unscrewed when disassembly is carried out. It is unacceptable that any elements of the product or constituting
its coherence are not correctly fastened/applied or pose a threat by their incorrect isolation from other functioning factors that in
contact would cause danger.
1.4 Guidelines for ESD security principles
To prevent damage to the product, system, or electrical components by electrostatic discharge (ESD), it is vital to be properly prepared
and to handle device(s) with care. The following measures are generally sucient to protect the product against ESD:
Do not use metal straps or wristbands on your hands to prevent static discharge.
Touch a grounded metal object rst before using/performing the maintenance (if possible) of the device.
When handling electrical equipment, avoid contact with pins, connectors, and any energy relays.
When moving electronic components, it is recommended to grab only their (isolated) edges, where there is no current ow. Do not
touch components, integrated circuits, memory modules, contacts, etc.
All electronic devices should be placed back into antistatic bags (if possible) when they are not in use.
1.5 Transport
During transport, store the product only in the original packaging to protect against shocks and bumps. Do not throw the packaging in
the trash. When shipping a product under warranty, the product must be in its original shipping box.
1.6 Warranty
The warranty does not apply in the event of product failures and defects resulting from improper use and handling of the device
(not under this user manual). Mechanical damage is the basis for rejecting a complaint. To correctly submit a warranty claim, contact
yourretailer.
1.7 Unpacking and examination
In the presence of the carrier, carefully unpack the product from the shipping box and make sure to check whether:
Contents of the package include all the elements listed in point 1.3.
All items are undamaged.
In case of absence, damage, discrepancies in the elements contained in point 1.3, a damage report has to be drawn up (if any occurred),
and the matter has to be submitted to the seller. The following are required: photographs, batch number, and description of the problem.
Indicated actions should be carried out on the same day as the date of product delivery.
1.8 Storage and ventilation
The product should be installed only in locations with limited access (separate rooms for equipment, etc.).
Do not install and store the device in places with water (still or running), humidity, or any other liquid substances being present.
Avoid exposing the product to direct sunlight sources.
Place the device on a stable, dry surface in a well-ventilated place. Leave at least 100 mm of free space around it to ensure
adequateventilation.
The device is designed to work only in a controlled environment (controlled temperature and humidity according to the data in the
specication, indoors, without conductive pollution present [dust, ammable gases, corrosive substances, etc.]).
Lanberg © 2015-2021
4EN
2. Assembly
Be sure to strictly follow the instructions in this manual.
2.1 Preparations
Prepare the appropriate amount of free space on the surface on which the assembly will take place. Carefully remove all elements from
the transport box. Further assembly instructions will be based on the diagram provided
2.1.1. Table of components
Cabinet items
Item No. Name Drawing Required ammount Supplied ammount
Item A Front glass door 1 pc. 1 pc.
Item B Rear door 1 pc. 1 pc.
Item C Side panel 2 pcs 2 pcs
Item D Frame 2 pcs 2 pcs
Item E Top cover 1 pc. 1 pc.
Item F Bottom cover 1 pc. 1 pc.
Item G Connect Bar 15U~27U 4pcs
32U~42U 6 pcs
Item H Fan cover 1 pc. 1 pc.
Item I Mounting rail 4 pcs 4 pcs
Item J Entry panel Flat 3 pcs
With a groove 4 pcs
i
Lanberg © 2015-2021 5
EN
Item K Adjustable feet 4 pcs 4 pcs
Item L Castors with breaker 4 pcs 4 pcs
Item M Door stopper 15U~ 27U 8 pcs
32U~42U 12 pcs
Item N Swing handle lock 1 pc. 1 pc.
Item O Small round lock 3 pcs 3 pcs
Item W Front door spacers 2 pcs 4 pcs
Screws
Item No. Name Drawing Required ammount Supplied ammount
Item P M8 Flange nut 8 pcs 9 pcs
Item Q M8 Allen head bolt 16 pcs 17 pcs
Item R M5*10 Self-tapping screw
15U~ 27U 36 pcs 40 pcs
32U~42U 44 pcs 50 pcs
Item S M4*8 Self-tapping screw 15U~ 27U 20 pcs 23 pcs
32U~42U 26 pcs 30 pcs
Item T M6 Snap nut
15U~ 27U 32 pcs 35 pcs
32U~42U 48 pcs 50 pcs
Item U M6x12 Allen Head Bolt
15U~ 27U 32 pcs 35 pcs
32U~42U 48 pcs 52 pcs
Item V M6 Accessory screw
andnuts 20 pcs 20 pcs

Właściciel serwisu: TERG S.A. Ul. Za Dworcem 1D, 77-400 Złotów; Spółka wpisana do Krajowego Rejestru Sądowego w Sądzie Rejonowym w Poznań-Nowe Miasto i Wilda w Poznaniu, IX Wydział Gospodarczy Krajowego Rejestru Sądowego pod nr KRS 0000427063, Kapitał zakładowy: 40 618 750 zł; NIP 767-10-04-218, REGON 570217011; numer rejestrowy BDO: 000135672. Sprzedaż dla firm (B2B): dlabiznesu@me.pl INFOLINIA: 756 756 756