Znaleziono w kategoriach:
2
EN – INSTRUCTIONS
BOX CONTENTS
−Camera (baby unit)
− Parent unit
− 2× USB-C cable + 2× adapter
− Accessories for wall mounting
−Reset pin
−Instructions
−Safety instructions
PRODUCT LAYOUT
Camera (baby unit)
6
8
9
7
1
2
3
4
5
1. Status LED
a. Red light (ashing) – waiting to pair
b. Blue light (steady) – camera connected
c. Red light (steady) – connection problem
2. Microphone
3. CALL/PAIR button
4. Night light
5. MicroSD card slot
6. Speaker
7. USB-C port
8. Reset button
9. Wall mounting
2 3
Display (parent unit)
MENU
OK
4
2
10
12
11
1
3
13
5
6
7
8
14
15
16
9
1. Microphone
2. Charging status LED
a. Orange light – charging
b. Green light – fully charged
3. Power-on status LED
a. Orange light – device is on
4. ZOOM button
5. MENU button
6. DIRECTION buttons
7. OK button
8. CALL button
9. BACK button
10. Antenna
11. ON/OFF button
12. Speaker
13. Base
14. SD card slot
15. Reset button
16. USB-C port
WHERE TO PLACE THE UNIT
1. On a horizontal and solid surface
2. On a vertical surface
a. Use the included mount. It is marked which side is up.
b. In the box, you will nd a set of screws and plugs to screw the mount onto a solid, clean and at
surface.
c. Once the mount is rmly attached, snap the bottom of the camera into it and make sure it is secure.
4
3. Using the tripod thread
a. Place and secure the TrueLife NannyCam Holder (sold separately) to the chosen location.
b. Screw the camera onto the thread.
PAIRING THE CAMERA TO THE PARENT UNIT
Simply pair the camera and parent unit using the steps below.
Pairing:
1. When pairing, place the camera and parent unit as close as possible to each other.
2. Press the MENU button, use the ARROW buttons to move to the settings icon and conrm with the
OK button. In settings, navigate to the camera icon and conrm again.
3. Select Camera 1.
4. Hold the CALL/PAIR button on the camera for about 5 seconds until you hear a beep.
5. Press the OK button on the parent unit.
6. Pairing is conrmed by a blue LED on the camera and a notication on the parent unit.
Unpairing:
If connection problems exist between the camera and the parent unit, you can unpair and re-pair the
camera.
1. Press the MENU button, use the ARROW buttons to move to the settings icon and conrm with the
OK button. In settings, navigate to the camera icon and conrm again.
2. Select Camera 1.
3. Long press the OK button and the camera will disconnect from the parent unit.
4. Re-pair the camera and parent unit using the steps described above.
Pairing a second camera:
It is possible to purchase a second camera and pair it with the same parent unit. The pairing process is
the same, simply select „Camera 2“ during the pairing process.
PAIRING WITH THE APP
The camera can be paired with the parent unit and the smartphone app at the same time.
1. Download the app
Scan the QR code or enter the URL:
truelife.eu/57714/app
2. Register or log in with your existing account
a) Sign up
1. If you don‘t have an account in the app yet, press Sign Up. Select your country/region and ll in your
email address. Please read the Privacy Policy carefully and check the I Agree box.
2. Next, press Get Verication Code and write down the six-digit code you receive in your email inbox.
3. Now set your password (6-20 characters with a combination of letters and numbers) and press Done.
Note: The code is only valid for 60 seconds. If you have not used it within that time, press Resend and ll in
the code again. If you do not receive the code again, check your email spam folder.
b) Sign in with an existing account
1. If you already have an account in the app, press Log In. Select country/region, ll in your email
address and enter your password.
Adding a device to the app
1. Press Add Device.
4 5
2. In the left column, select Baby monitor and press TrueLife NannyCam R7 Dual Smart.
3. If you already have the camera paired with the parent unit, you now need to reset it using the reset
button on the back of the camera (at this point the parent unit will lose signal - it will reconnect after
a while). Hold the button for about 5 seconds until you hear a beep and the camera status LED turns
red and starts ashing.
4. In the app, conrm that the camera indicator is ashing and press Next. Select your home Wi-Fi
(2.4GHz), enter the Wi-Fi password and press Next.
Note: The app requires location access to pair properly.
5. A QR code will be displayed in the app. Hold it in front of the camera lens at a distance of 15 to 20 cm.
When pairing is successful, you will hear a beep and the camera‘s status light will ash blue. Press
I Heard a Prompt and wait until the pairing is complete which you will see in the app.
6. When it is completed, press Done. The camera is now ready to use.
Alternative pairing procedure
In the app, select Add Device. In the left column, choose Security & Video Surveillance and then se-
lect Smart Camera (Wi-Fi). In the top right corner, click on QR Code for Camera and then select EZ
Mode. Even though there isn‘t an LED indicator on the camera, check the box Make sure the indicator
is ashing quickly. Select Wi-Fi (2.4 GHz), enter the password for that Wi-Fi, and press Next and wait for
the camera to pair. When the pairing is successful, the audio signal „Connect router“, „Connect internet“
and „Add device success“ will be heard. When nished, select Done. The camera is now ready to use.
Video tutorial for pairing methods
Scan the QR code or enter the URL:
truelife.eu/01488/pair
ROTATING THE CAMERA
Remotely control and rotate the camera at any time, using either the parent unit or the smartphone
app. Just wake up the parent unit by pressing the ON/OFF button and use the DIRECTION buttons to
rotate the camera in any direction.
Note: If you are using two cameras, the main screen will be split into two parts. One of the cameras must
be selected rst. Select one of the cameras by pressing the ZOOM button and conrm with the OK button.
TAKING PHOTOS AND VIDEOS
To take photos or videos, a microSD card (not included) is required. The card can be inserted either
in the camera (baby unit) or the parent unit. The card must be formatted in FAT32 format for proper
functionality. The maximum supported card size is 128 GB. We recommend using a microSD card with
at least Class 10 / UHS-1 parameters.
a. If you insert a microSD card into the camera, the recording is controlled via the app and the recor-
ding will be captured to the phone gallery and the card at the same time.
b. If you insert a microSD card into the parent unit, the recording is controlled via the parent unit and
the recording will be made to the card in that unit.
TRUELIFE SMARTCARE®
The baby monitor features TrueLife SmartCare®, which alerts you (via a notication on the unit/phone
display and with an audible signal) to motion, noise and crying. To turn on these features and set them
up, follow these steps: