Znaleziono w kategoriach:
Power audio (8)
Wróć
EN - ENGLISH
Party Box 810
Bluetooth portable speaker
User Manual
NOTES ON USE
•
This is a precision electronic appliance; avoid using it in the following cases:
•
Listening to high volume for a long time could damage your hearing.
•
Do not close the ear to the loudspeaker during step setting and volume adjustments, and in
particular keep the volume down at the ignition
•
Near strong heat sources, such as central heating plants or stoves.
•
In very humid places such as bathrooms, swimming pools, etc.
•
In very dusty places.
•
In places subject to strong vibrations.
•
Position the appliance in such a way that there is always enough room for free air circulation
(at least 5 cm).
•
Do not block the air inlets.
•
If any liquid enters the appliance, unplug it immediately from the socket and take it to the
nearest authorized service center.
•
Before switching on the appliance, always check that the power cable and the connection
cable are properly installed.
•
The apparatus shall not be exposed to dripping or splashing water. No objects filled with
liquid, such as vases, should be placed on the unit.
•
No naked flame sources, such as lighted candles, should be placed on.
•
Power adaptor must be connected to a socket close to the device and must be easily
accessible.
•
If you notice excessive heat on the device or power adaptor, disconnect the plug from the
main power socket immediately.
•
Do not pull the power cord
•
Keep this manual.
CARE AND MAINTENANCE
Use a slightly damp soft cloth for cleaning. Do not use solvents and abrasive substances.
IMPORTANT
This device is designed for home use (not professional use). This appliance has been
carefully built to ensure long-lasting perfect performance. However, should any
inconvenience occur, please contact your local authorized Service Centre.
follows a policy of ongoing research and development. Therefore products may have different
features from those described.
TECHNICAL SPECIFICATIONS
•
Power Source AC:100-240V 0.8A
•
Power Consumption MAX 60W
•
RMS Power 40W
•
Bluetooth version V5.0
•
BT channel emission power 0dBm
•
Bluetooth frequency 2402 MHz~2480MHz
•
Bluetooth range >10M
•
FM frequency 87.5Hz-108.0MHz
•
Battery type 8V,7A Lead-acid battery
•
Speakers 6.5” 3 Ohm
•
Frequency response 60Hz-16kHz
•
Product dimensions 26.9(L)×29(D)×62.6(H)
LOCATION OF CONTROL
(01)
POWER (Stand-by)
(02)
MODE button
(03)
PREV button (previous song)
(04)
NEXT button (next song)
(05)
LED (LIGHT SW button)
(06)
REC button
(07)
MENU (treble / bass /microphone vol /
microphone echo /guitar vol) adjustment
(08)
Play/Pause button (long press TWS)
(09)
VOLUME
(10)
GT input
(11)
MIC input
(12)
AUX / FM input
(13)
TF Card input
(14)
USB input
(15)
AC 100-240V input
REMOTE CONTROL
(01)
Power ON/ Stand-by
(02)
MUTE button
(03)
REC button (Press to start recording. Press again to
stop recording)
(04)
Mode function (select between AUX/USB/SD/FM/
BLUETOOTH)
(05)
Volume +
(06)
Next song/CH+
(07)
Previous song/CH-
(08)
Play/Pause/TWS
(09)
(Single Repeat/ Repeat All)
(10)
EQ Sound Mode Key (POP / ROCK / JAZZ / CLASSLIC /
FLAT)
(11)
Volume –
(12)
Numeric buttons
Installing the Batteries
Remove the battery cover from the Remote Control and put 2xAAA size batteries inside the
compartment. The diagram inside the Battery compartment shows the correct way to install the
batteries.
TRANSPORTATION
For transportation, use the upper handle, slightly fold the appliance and use the two rear wheels.
POWER
This unit works with 8V/7A lead acid rechargeable battery and 100-240V power supply.
When the battery is being phased out and the device does not turn on, plug the power cord into the
Power socket (15) on the device and plug into a wall socket to recharge.
Lamp status LED charging:
- Red LED indicator: The device is charging.
- Green LED indicator: The battery is charged.
Caution:
- Do not connect the appliance to sockets with a voltage other than indicated one.
BASIC FUNCTIONS
POWER ON/OFF
Long press the main ON/OFF power switch (01) to position ON to turn the power.
BATTERY CHARGE
- Connect the charging cable to the charging plug (15) the charging function and the LED
indicating charging status will start immediately.
For a longer battery life it is recommended to disconnect the main power cable after 10 hours max
of recharging.
If the battery is empty, please turn the speaker off and recharge for at least half an hour
before using it again.
STAND-BY
You can switch the system to standby mode using the
button (01) on remote control:
Press it again to Switch On the unit. Caution:
- In standby mode the battery is NOT recharged and the device has a minimum battery
consumption.
- When connecting the main power supply, long-press the power button (01) for 3 seconds,
the device will display turned
on. Which means it works normally. Short press the power button (01), the device will display
entering into stand-by mode. At the same time, the power button shows red light.
- For long periods of inactivity, it is necessary to disconnect the mains cable and recharge
the battery periodically.
PLAYBACK MODE SELECTION FUNCTION
To change the mode function, press the key (02) on the unit or press button (04) on
remote control to select: BLUETOOTH (the display BLUE), USB/SD (only if the USB socket (14)/
Micro SD (13) is connected to a memory, the display shows for a few seconds "USB" or "SD"),
AUX-IN (the display shows "LINE" or "FM").
ADJUSTING THE VOLUME
1. Turn the Main Volume control (09) to increase or decrease the overall volume of playback, or
use the buttons (05) and (11) on the remote control;
2. Press the button (07) and turn the knob (09) (treble / bass / microphone vol / microphone
echo / guitar vol) adjustment
PRE-EQUALIZER
This unit has a pre-set audio equalization system. Press the unit or the EQ button (10) on the
remote control repeatedly to select one of the 5 audio equalizations available and which best suits
the current sound reproduction.
SETTING TONE TREBLE AND BASS
Press the
MENU (07) key (1) time to adjust the treble and (2) times to adjust the bass.
MASTER VOLUME
Turn the (09) knob to adjust the main volume
MIC ECHO EFFECT
Press the MENU (07) key (4) times and rotate the master volume knob (09) to adjust the
microphone echo adjustment.
Note: the echo only works on microphone inputs.
MIC TONE
Press the MENU (07) key (3) times and rotate the master volume knob (09) to adjust the
microphone sound level.
Note: This function is available only when a wired microphone is connected (not provided)
GT TONE
Press the MENU (07) key (5) times and rotate the master volume knob (09) to adjust the
sound level of the guitar.
Note: Only when a GUITAR device is connected.
LED LIGHT
Press the LED button (05) several times to select the Moving Disco-Light effect, each press will
correspond to a lighting effect.
ON/OFF VOICE PROMPT FUNCTION
Press and hold MODE button (02) on unit or button (04) on remote control to switch
ON/ OFF the voice announcement.
BLUETOOTH FUNCTION
1.
Switch On and press the MODE (02) on unit, or button (04) on remote
control to select the Bluetooth function, the display shows "BLUE";
2.
In the Bluetooth mode, the "BLUE" on display will star flashing, the system
automatically enters pairing mode;
3.
Activate the Bluetooth feature on the external device;
4.
Search the available devices and select " AKAI PARTY BOX 810 ";
5.
Enter the password "0000" if required;
6.
Press the Play/Pause button (08) on the unit o (08) button on remote control to star t
playing, or use PREV button (03) or NEXT (04) on unit, or the keys (6) and (7) on
remote control to select a song.
TWS FUNCTION OPERATION
(True wireless stereo technology) TWS technology enables user to make wireless connection
between two speakers which are same model and compatible with TWS. In TWS connection, two
speakers will be automatically grouped to be a Stereo- Speaker System which outputs the left and
right channel.
CONNECTION MODE
Notice: Two speakers must be same model and both compatible with TWS.
1. Please switch on both speakers and select "Bluetooth" mode;
2. Press and hold PLAY button (08) on the unit, you will hear a "beep". It becomes the main
speaker (left channel), which will automatically search and connect with another speaker
(right channel). After connection, you will hear a "beep";
3. Connect mobile phone or Bluetooth player to the speaker by Bluetooth. After connection,
you can play music with the TWS Stereo- Speaker System.