Znaleziono w kategoriach:
Płyty główne (116)
Wróć
The items labeled below correspond to the installation steps, for steps
and more information on the steps, please refer to the rest of the guide.
Support
SEEKING A SOLUTION?
Scan now for assistance
BATTERY
LGA1851
MAXIMUS Z890 EXTREME
CPU_12V_1 CPU_12V_2
CPU_PROTECT_LED
CPU_12V_LED
HDMI
PCIEX16(G5)_1
PCIEX16(G5)_2
SATA6G_3
SATA6G_4
SATA6G_1
SATA6G_2
AUDIO
U10G_E123
U10G_EC4
LAN1_U10G_1
U10G_C3
LAN2_U10G_2
M.2(TBT5)_1
M.2(TBT5)_2
U20G_C5
M.2(WIFI)
U5G_E12U5G_E34
M.2_2(SOCKET3)
M.2_1(SOCKET3)
2280
M.2_4(SOCKET3)
2280
2280
22110
22602242
M.2_3(SOCKET3)
2280
22110
22602242
HD_LED
22602242
FLBK_CL_CMOS
ADD GEN2_3ADD GEN2_4
CPU_BCLK- SOC_BCLK+
CPU_BCLK+ SOC_BCLK-
F_AUDIO
USB_E34USB_E12
RSVD_4
PCIEX4(G4)
F_PANEL
22422260
LED2
LED1
PAUSE_LED
RETRY BUTTON
BIOS_LED1
BIOS_LED2
SAFE_BOOT
T_SENSOR LN2_MODE
RSVD_1 RSVD_2
BIOS_SELECT
DDR5 DIMM_B21st (64bit, 288-pin module)
DDR5 DIMM_B1 (64bit, 288-pin module)
DDR5 DIMM_A21st (64bit, 288-pin module)
DDR5 DIMM_A1 (64bit, 288-pin module)
ATX_PWR
U10G_C4
U20G_C9
BOOT
VGA
DRAM
CPU Q_CODE
START
FLEXKEY
CHA_FAN2
RAD_FAN1
RAD_FAN2
W_PUMP+2
CPU_FAN
CPU_OPT
CHA_FAN1
ADD GEN2_12
Intel®
Z890
WB_SENSOR
DIMM.2_SLOT
ProbeIt ProbeIt
ALT_PCIE_MODESLOW_MODE
PAUSE BIOS_SWITCH
W_PUMP+1
PCIE_8PIN_PWR
PCIE_8PIN_LED
ARGB
ARGB
USB 10Gbps
Chassis Fan
USB 20Gbps
USB 5Gbps
USB 5Gbps
USB 2.0 Front Panel System
Front Panel Audio
2
Q24454 / Revised Edition V2 / August 2024
Prepare the components
NOTE: The components listed above are recommendations, please prepare components according to your needs.
Chassis
CPU Memory M.2 SSD
SATA device
Power supply unit Graphics card
CPU Cooler
• Install the Memory
NOTE: Please refer to the manual(s) for more information: Motherboard
Install key components
• Install the CPU
NOTE: Do not remove the PnP cap before the CPU is properly installed.
Thermal paste
OROR
Please refer to the manual(s) for more information: Motherboard
Please scan for more
information on CPU
installation steps.
3
• Install the M.2 SSD
M.2 Q-Release M.2 Q-Slide
NOTE: Please refer to the manual(s) for more information: Motherboard
OR
Remove
M.2 slot
Remove Optional
M.2 slot
Make sure of the following:
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
Make sure the M.2 Q-Slide clicks and
locks the M.2 SSD
Type-A Install
RemoveType-B
M.2 slot
M.2 slot
Additional Information (on selected models)
• M.2 Q-Latch
clicks and locks
the M.2 SSD
• Secure the
screw properly
• Insert the pin
of the M.2 Anchor
into the hole
4
Install the motherboard into the chassis
For non pre-mounted I/O
shield models only
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis
Install the cooling system
• Air Cooler
• AIO Cooler
AIO_PUMP / W_PUMP
(connect to pump)
CPU_FAN / CPU_OPT
(connect to radiator)
CPU_FAN / CPU_OPT
OR
NOTE: Please refer to these manual(s) for more information: Cooler Chassis
5
Connect cables from Chassis
Ground
+5V
Data
ARGB header
Connect to chassis fan and ARGB/RGB headers
B
R
+12V G
RGB header
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis Fan
Chassis fan
Install and connect the power supply unit (PSU)
Make sure the PSU is secured to
the chassis using screws, and that
the chassis has proper airflow
Chassis PSU
NOTE: Input: AC 100~240V, 6A/3A, 50/60Hz
Please refer to the manual(s) for more information:
• Connect the power cables to the motherboard
OROR
Connect cables from PSU
Motherboard PSU
NOTE: Please refer to the manual(s) for more information: