Znaleziono w kategoriach:
Ekspres CAMRY CR 4405G

Instrukcja obsługi Ekspres CAMRY CR 4405G

Powrót
(GB)
(F) mode d'emploi (E) manual de uso
(P) manual de serviço (LT) naudojimo instrukcija
(LV) lietošanas instrukcija (EST) kasutusjuhend
(CZ) návod k obsluze (RO) Instrucţiunea de deservire
(GR) οδηγίες χρήσεως (BIH) upute za rad
(H) felhasználói kézikönyv (FIN) käyttöopas
(MK) Упатство за корисникот (PL) instrukcja obsługi
user manual (D) bedienungsanweisung
CR 4405
2
3
2
1
4
5
22
6,7
9
10a
11
12
14,15
16
13
10b
17
21
8
18
19
20
The warranty conditions are different, if the device is used for commercial purpose.
1. Before using the product please read carefully and always comply with the following
instructions. The manufacturer is not responsible for any damages due to any misuse.
2.The product is only to be used indoors. Do not use the product for any purpose that is not
compatible with its application.
3. The appliacable voltage is 230V, ~50Hz. For safety reasons it is not appropriate to
connect multiple devices to one power outlet.
4. Please be cautious when using around children. Do not let the children to play with the
product. Do not let children or people who do not know the device to use it without
supervision.
5. WARNING: This device may be used by children over 8 years of age and persons with
reduced physical, sensory or mental capabilities, or persons without experience or
knowledge of the device, only under the supervision of a person responsible for their
safety, or if they were instructed on the safe use of the device and are aware of the
dangers associated with its operation. Children should not play with the device. Cleaning
and maintenance of the device should not be carried out by children, unless they are over
8 years of age and these activities are carried out under supervision.
6. After you are finished using the product always remember to gently remove the plug
from the power outlet holding the outlet with your hand. Never pull the power cable!!!
7. Never leave the product connected to the power source without supervision.
8. Never put the power cable, the plug or the whole device into the water. Never expose
the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use
the product in humid conditions.
9. Periodically check the power cable condition. If the power cable is damaged the product
should be turned to a professional service location to b e replaced in order to avoid
hazardous situations.
10. Never use the product with a damaged power cable or if it was dropped or damaged in
any other way or if it does not work properly. Do not try to repair the defected product
yourself because it can lead to electric shock. Always turn the damaged device to a
professional service location in order to repair it. All the repairs can be done only by
authorized service professionals. The repair that was done incorrectly can cause
hazardous situations for the user.
11. Never put the product on or close to the hot or warm surfaces or the kitchen appliances
like the electric oven or gas burner.
12. Never use the product close to combustibles.
Even when
use is interrupted for a short time, turn it off from the network, unplug the power.
13. Do not let cord hang over edge of counter.
14. This equipment is intended for domestic and similar use, such as: staff kitchens in
stores, offices and other work environments, utility rooms, by customers in hotels, motels
and other residential environments of this type, in bedrooms and dining rooms.
15. The device has to be turned off after every use.
16. In order to provide additional protection, it is recommended to install residue current
device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact
professional electrician in this matter.
ENGLISH
ENGLISH
SAFETY CONDITIONS
IMPORTANT INSTRUCTIONS ON SAFETY OF USE
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
3
17. Never use the appliance without water! It can cause damage.
18. Never direct a steam or hot water jet toward the body.
19. Never use carbonated water!
20. Never leave the appliance at a temperature below 0 °C as it can cause damage.
21. Before filling the water tank with water, always disconnect the appliance from the mains.
22. Before cleaning, always disconnect the espresso machine from the power supply and
wait until all hot parts have cooled. The appliance should be cleaned with a mild detergent
(without abrasives). Never use a solvent for cleaning, as this can damage the paint.
23. To decalcify the appliance, use espresso machine liquid decalcifier.
24. Never touch the filter holder or the milk frothing nozzle while the appliance is in
operation, as this may cause burns.
DESCRIPTION
1 - Cup Warmer 2 - Top Rail 3 - Water Tank Lid 4 - Water Tank
5 - Steam Knob 6 - ON/ OFF Indicating Lamp 7 - Ready Lamp 8 - Steam Lamp
9 - ON/ OFF Switch 10 - Coffee/ Hot Water Button 11 - Steam Button 12 - Filter Holder Handle
13 - Drip Water Tray 14, 15 - Base 16 - Water Outlet 17 - Milk Frothing Nozzle
18 - Coffee Measuring Spoon 19 - Ground Coffee Filter 20 - Filter Holder 21 - Coffee Outlet
22 - control lamps
BEFORE FIRST USE
After unpacking the appliance, make sure that all the buttons are off and the Steam Knob (5) is switched to the right. Before use, wipe the
appliance (please see "Cleaning and Maintenance"). Remove the Water Tank (4) and fill it up to MAX. It is recommended to use filtered
water. This prevents lime build-up and improves the taste of the prepared coffee. Do not use carbonated water. After filling the Tank (4)
with water, put it in its place. Remove the Steam Nozzle (17). Then install the Filter Holder (20) by placing it below the Water Outlet (16)
and turning it to the right. Place a cup under the installed Filter. Connect the power cord and press the ON/OFF Switch (9). The ON/ OFF
Indicating Lamp (6) will light up. After reaching adequate temperature lamp will stop blinking. Press the Coffee/ Hot Water Button (10)
immediately and wait until water starts to flow out of the filter. This means that the hydraulic system of the appliance has been filled with
water.
NOTE: If have not used your machine for a few days, it is recommended that you pass at least one cup of water through the hydraulic
system.
PREPARING CAPPUCCINO
To prepare cappuccino, you need already brewed espresso and frothed milk warmed up using steam in a separate jug (preferably made
of metal or stainless steel).
Prepare espresso (please see "Preparation"). Pour cold milk into a cooled metal jar. Make sure that the Tank (4) is filled with water. Press
the Steam Button (11). . Place a container of your choice
under the Nozzle (17) and turn the Knob (5) to the left. At the beginning, some water will
come out of the Nozzle and then a strong jet of steam will start to flow out. Turn the Knob (5) clockwise and place the metal jug filled with
milk under the Nozzle (17). Place the Nozzle in the milk and turn the Knob (5) counterclockwise. Coming out of the Nozzle, the steam will
start to froth and warm the milk in the jug. While milk is being frothed, rotate the jug around the Nozzle. To avoid hot milk splashing, never
remove the Nozzle from the milk unless the Knob (5) is turned to the right. In order to avoid heating the jug with milk, make sure that the
Nozzle does not directly touch its bottom or sides. The milk should be frothed on the surface and right under it. If steam does not come
out, the Nozzle may be clogged. When the milk is sufficiently frothed and warmed up, press the Steam Button (11) to complete the
operation. Set the jug with the frothed milk aside for a moment. Then pour the milk into your cup of espresso. After use, press the ON/
OFF Switch (9) and disconnect the appliance from the power supply. If the interval between twice operations is more than 25 minutes, the
appliance will shut off automatically.
: a - 30 ml; b - 60 ml
HEATING THE ESPRESSO MACHINE
It is important to heat the appliance so that the brewed coffee would have the right temperature. Make sure that the Steam Knob (5) is
closed and there is water in the tank (4). Place the jug under the Steam Nozzle (17). Insert the Filter (19) into the Filter Holder handle (20)
and place it under the Water Outlet (16). If you want the cups to be heated, place them on the Cup Warmer (1). Turn on the machine (9).
Lamp (7) will blink. After reaching adequate temperature lamp will stop blinking. Place the cups on the Tray (13) and press the Coffee/ Hot
Water Button (10). Wait until two cups of water flow out. Push ten button (11). Indicating Lamp (8) will light up. After reaching adequate
temperature lamp will stop blinking. Turn the Steam Knob (5) to the left and wait until a small amount of water flows into the cup. Close the
Steam Knob (5) and switch all buttons off.
PREPARING ESPRESSO
The machine is used for preparing espresso. All other beverages (e.g. café latte, latte macchiato are cappuccino) are espresso-based.
Measure the appropriate amount of coffee and place it in the filter (19). To prepare espresso, use one coffee measuring spoon (18). Make
sure that the coffee has been ground properly. Then place the Filter with the coffee inside in the Filter Holder (20). Place the Filter Holder
in the machine, turning it approximately 45 degrees to the right. Fill the Water Tank (4) with cold water. Connect the appliance to a mains
socket. NOTE: Remember that the device requires grounding. Turn on the machine (9). Lamp (7) will blink. After reaching adequate
temperature lamp will stop blinking. Press the Coffee Button (10). The brewed coffee will start to flow down through the Coffee Outlet (21).
To stop brewing, press the Coffee Button again (10). To remove the Filter Holder (20), turn it to the left. To facilitate Filter Holder removal,
turn the Knob (5) counter-clockwise to release the pressure.
NOTE: Never remove the Filter Holder (20) during brewing, that is, when the Coffee Button is on (10). After use, press the ON/ OFF
Switch (9) and disconnect the appliance from the power supply.
Lamp (8) will blink. After reaching adequate temperature lamp will stop blinking.
Never use the Knob (5) while the Lamp (8) is off.
4
DEUTSCH
CLEANING AND MAINTENANCE
NOTE: Before cleaning, disconnect the machine from the mains and wait until it has cooled down completely.
Detach the Filter Holder and remove used coffee from the Filter. If the Filter holes are clogged with coffee, use a brush to clean it. If the
holes in the Filter Holder are clogged, clean it with a brush. Always empty the Water Tank after use. From time to time, clean the Water
Tank with a damp sponge or cloth. The cups, Water Tank, Drip tray, Tray Base, Filter and Filter Holder may be washed in water with some
mild detergent without abrasive substances or solvents. External parts should be cleaned with a soft cloth or sponge. Highly abrasive
cleaners or brushes may cause surface scratches.
DECALCIFICATION
If coffee brewing takes a longer time or the Nozzle does not produce steam, the appliance should be decalcified. If hard water is used, the
espresso machine should be decalcified after it has been used approximately 40 times. If soft water is used, however, the machine can be
decalcified after it has been used approximately 80 times. Espresso machine liquid decalcifier may be used for decalcifying the appliance.
Before decalcifying, make sure that the machine is disconnected from the power supply.
1) Pour approximately 250 ml of lukewarm water and then add 250 ml of espresso machine liquid decalcifier.
2) Place the Filter Holder on the machine. Then place a cup half-filled with cold water under the Nozzle and an empty cup under the Filter
Holder.
3) Connect the appliance to the power supply.
4) Press the ON/ OFF Switch (9).
5) Then press the Coffee Button (10).
6) When the decalcifier starts to flow down into an empty cup, insert the tip of the Nozzle into a cup filled with cold water and press the
Steam Button (11).
7) Wait for a few seconds and switch off the appliance.
After decalcifying, the espresso machine must be rinsed three times with clean water. To do this, repeat steps 1 to 7 filling the water tank
(4) with clean water.
TECHNICAL DATA:
Capacity max: 1,0l
Voltage: 220-240V ~50Hz
Power: 850W
Device is made in class I of insulation and has to be connected only to power outlet
with ground circuit. Device is compliant with EU directives:
- Low voltage directive (LVD)
- Electromagnetic compatibility (EMC)
Device marked CE mark on rating label
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
DEUTSCH
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
LESEN SIE AUFMERKSAM WICHTIGE ANWEISUNGEN BEZÜGLICH DER SICHERHEIT
DER BENUTZUNG BEWAHREN SIE DIESE FÜR DIE ZUKUNFT AUF
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1. Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die aufgrund
von bestimmungswidriger Nutzung oder unsachgemäßer Bedienung entstanden sind.
2. Das Gerät ausschließlich an die Steckdose 230 V - 50 Hz anschließen. Es darf nicht zu
anderen, bestimmungswidrigen Zwecken benutzt werden.
3. Wegen Vorsichtsmaßnahmen, sollten keine weiteren Geräte an den gleichen Stromkreis
angeschlossen werden.
4. Falls sich Kinder in der Nähe befinden, sollte bei der Nutzung des Gerätes spezielle
Vorsicht bewahrt werden. Dieses Gerät ist nicht zum Spielen für Kinder, sowie für
Erwachsene, die sich mit der Bedienungsanleitung nicht vertraut gemacht haben, geeignet.
5. WARNHINWEIS: Dieses Gerät kann von Kindern im Alter von über 8 Jahren sowie von
Personen von einer beschränkten körperlichen, sensorischen, psychischen Fähigkeit oder
von Personen, die keine Erfahrung oder kein Kenntnisse von dem Gerät haben, nur dann
genutzt werden, wenn die Nutzung unter Aufsicht einer Person, welche die Verantwortung
für deren Sicherheit trägt, stattfindet oder diesen Personen Ratschläge bezüglich der
sicheren Benutzung des Geräts erteilt wurden und sie sich den mit seiner Benutzung
verbundenen Gefahren bewusst sind. Kinder dürfen nicht mit dem Gerät spielen. Die
Reinigung und die Unterhaltung des Geräts dürfen nicht von Kindern durchgeführt werden,
5

Właściciel serwisu: TERG S.A. Ul. Za Dworcem 1D, 77-400 Złotów; Spółka wpisana do Krajowego Rejestru Sądowego w Sądzie Rejonowym w Poznań-Nowe Miasto i Wilda w Poznaniu, IX Wydział Gospodarczy Krajowego Rejestru Sądowego pod nr KRS 0000427063, Kapitał zakładowy: 40 618 750 zł; NIP 767-10-04-218, REGON 570217011; numer rejestrowy BDO: 000135672. Sprzedaż dla firm (B2B): dlabiznesu@me.pl INFOLINIA: 756 756 756