Znaleziono w kategoriach:
Laminatory (2)
Wróć
HOME &OFFICE DIN A3/250
Laminator
Laminator
E
SK
F
D
GB
I
S
PL
RUS
H
BG
CZ
TR
FIN
RO
GR
NL
P
Operating Instructions
Bedienungsanleitung
Mode d‘emploi
Instrucciones de uso
Gebruiksaanwijzing
Istruzioni per l‘uso
Instrukcja obsługi
Használati útmutató
Manual de utilizare
Návod kpoužití
Návod na použitie
Manual de instruções
Bruksanvisning
Руководство по эксплуатации
Ръководство за обслужване
Οδηγίες χρήσης
Kullanma kılavuzu
Käyttöohje
00
050562
Abb.1
Abb.2
1 2 3
4 6 7 5
2
GOperating Instructions
Machine setup
1. Laminate output (rear)
2. Roller unlocking (rear)
3. Connection cable
4. Laminate intake
5. On/Off switch
6. Ready status LED
7. Power status LED
1. Introduction
1.1 Foreword
Thank you for choosing aHama product.
Take your time and read the following instructions and information completely.Please keep
these instructions in asafe place for futurereference. If you sell the device, please pass
these operating instructions on to the new owner.
Note –Importance of the operating instructions
Failuretoobserve the operating instructions when using the product constitutes
incorrect use or wilful misuse and is not permitted.
1.2 Explanation of warning symbols and notes
Risk of electric shock
This symbol indicates arisk of electric shock from touching product parts carrying
hazardous voltage.
Warning
This symbol is used to indicate safety instructions or to draw your attention to specic
hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
1.3 Package contents
•"Home &Oce DIN A3 /250" Laminator
•5laminating pouches (DIN A3)
•These operating instructions
2. Security
2.1 Correct use
•This product is intended for the lamination of documents both in the home and in the
commercial sector,provided the applications arecomparable with typical household use
(e.g. in oces, workshops and hotels, etc.).
•Do not operate the product continuously,asitisnot designed for this.
•Use the product only for the intended purpose.
•The product is intended only for use inside buildings.
•Protect the product from dirt, moistureand overheating and use it in dry rooms only.
•Do not use the product in the immediate vicinity of heaters, other heat sources or in
direct sunlight.
•Do not use the product in adamp environment and avoid splashing water.
•Do not operate the product outside the power limits specied in the technical data.
•Do not use the product in areas in which electronic products arenot permitted.
•Do not drop the product and do not expose it to any major shocks.
•This product is not intended for use by persons, including children, with limited physical,
sensory or mental abilities or lacking in experience or knowledge, unless they are
supervised by aperson responsible for their safety or have been instructed on how to
use the product.
•As with all electrical products, this device should be kept out of the reach of children.
•Keep the packaging material out of the reach of children due to the risk of suffocation.
•Dispose of packaging material immediately in accordance with the locally applicable
regulations.
•Do not modify the product in any way.Doing so voids the warranty.
•Only use the article under moderate climatic conditions.
Note
The product is only intended for volumes generated by households.
Note –Commercial use
•If the device is used commercially,increased duty of carerequirements apply.
•Therefore, please observe the accident prevention regulations of the German
employer’sliability insurance association for electrical systems and equipment.
Please also observe all accident prevention regulations from other applicable
employer’sliability insurance associations and accident insurance companies, as well
as any legal regulations applicable to the particular industry and/or location.
2.2 Basic safety instructions
Please note the following safety instructions in order to use the device safely:
•Check the device beforeuse for any visible external damage. Do not put adamaged
device into operation.
•People who, as aresult of their physical, mental or motor capacities, areunable to
operate the device safely must only use the device under supervision or after instruction
by aresponsibleperson.
•Faulty components must only be replaced with original spareparts. Only these parts are
guaranteed to meet the required safety standards.
•Protect the device against moistureand the penetration of liquids or objects. In the
event of contact with liquid, disconnect the device from the power supply immediately.
Warning -Danger of burns on the housing
Do not touch the housing.
Risk of electric shock
•Do not open the device or continue to operate it if it becomes damaged.
•Do not use the product if the AC adapter,adapter cable or power cable is damaged.
•Do not attempt to service or repair the product yourself.Leave any and all service
work to qualied experts.
3. Installation /Setup
Warning
•Only operate the product from asocket that has been approved for the device. The
socket must be installed close to the product and must be easily accessible.
•Disconnect the product from the power supply using the On/Off switch –ifthis is not
available, unplug the power cordfromthe socket.
•If using amulti-socket power strip, make surethat the total power consumption of
all connected devices does not exceed the power strip's maximum throughput rating.
•If you will not be using the product for aprolonged period, disconnect it from
mains power.
Note
•Set the product up on alevel, horizontal and suciently stable and heat-resistant
surface.
•Route all cables so that thereisnorisk of tripping.
•Do not bend or crush the cable.
•Protect the connecting cable from hot surfaces and sharp edges.
•Always pull directly on the plug when disconnecting the cable, never on the cable
itself.
•The product must only be operated on asupply network as described on the type
plate.
•Connect the network cable to aproperly installed and easily accessible network socket.
4. Operation
Note
•Always set the correct temperaturefor the laminating pouch thickness being used.
•When laminating thicker paper or multiple pages, we recommend using athinner
pouch.
•Always wait until one laminating operation is nished beforestarting the next one.
•Do not allow the device to run for morethan two hours at atime.
•Wait around 15 seconds between two laminating processes.
•Laminating pouches of all sizes should be introduced into the centreofthe opening
on the front. Ensurethat the sealed end is introduced rst. (See Fig.2)
3
4.1 Switching the device on
•Move the On/Off switch (5) to the "COLD" or "HOT" position to switch the device on.
•The Power status LED (7) lights up solid blue.
4.2 Cold lamination
•Move the On/Off switch (5) to the "COLD" position for cold lamination.
Note
•If hot lamination was carried out beforehand, it can take up to around 40 minutes
beforethe device has fully cooled.
•Special pouches areneeded for cold lamination. The seal is created with pressure
rather than heat. It is not permanent and does not offer one hundred per cent
protection against oxygen and water.The process is suitable for heat-sensitive
documents, such as thermal paper,till receipts, driving licences or laser copies. In
other words, anything that would be damaged or altered by hot lamination.
•Wait until the Ready status LED (6) lights up solid red. The device is cool or is not
heating up.
•Place the object to be laminated in the corresponding cold lamination pouch.
•Guide the pouch into the middle of the front opening (4) on the device. Ensurethat the
sealed end (see Fig. 2) is introduced rst.
•The document is output again at the back (1).
•If the document has not been fully laminated, repeat the initial steps.
•To interrupt the lamination process (e.g. if the intake angle is incorrect), press the roller
unlocking button (2) and correct the position of the pouch.
4.3 Hot lamination
•Forhot lamination, move the On/Off switch (5) to the "HOT" position.
Warning -Danger of burns on the housing
•Do not touch the housing.
•Be awarethat laminated objects arehot.
•Place the laminated object on alevel surface to cool down in order to prevent it
from curling up.
Note
Special pouches areneeded for hot lamination. They aresealed using heat. This seal
is permanent and cannot be undone. Only objects that areinsensitive to heat should
be laminated. From apouch edge of around 4mm, the objects areprotected so they
arevirtually waterproof.The thickness of the pouch determines the object's stability /
kink protection.
•The Ready LED (6) lights up solid redonce the required temperaturehas been reached.
•Place the object to be laminated in the corresponding hot lamination pouch.
•Guide the pouch into the middle of the front opening (4) on the device. Ensurethat the
sealed end (see Fig. 2) is introduced rst.
•The document is output again at the back (1).
•If the document has not been fully laminated, repeat the initial steps.
•To interrupt the lamination process (e.g. if the intake angle is incorrect), press the roller
unlocking button (2) and correct the position of the pouch.
4.4 Switching the device off
•Move the On/Off switch (5) to the "OFF" position to switch the device off.
•Both status LEDs (6/7) go out.
•Remove the mains lead from the socket.
•Allow the device to cool down completely beforetidying it away.
5. Care and maintenance
Danger –risk of death from electric shock
Disconnect the mains plug from the socket beforestarting any cleaning work.
Warning -Danger of burns on the housing
Do not touch the housing.
Warning -damage to the device from moisture
Ensure, when cleaning, that no moisturepenetrates the device in order to avoid
irreparable damage to it.
The rollers on the laminator must be regularly cleared of dust and any glue residue. To do
so, proceed as follows:
•Switch the device on -asdescribed in 4.1 Switching the device on.
•Move the On/Off switch (5) to the "HOT" position.
•Wait until the Ready status LED (6) lights up solid red.
•Guide apiece of paper into the middle of the front opening (4).
•Repeat the process if thereisalot of dirt on the paper.
•Clean the outside of the device with aslightly damp cloth.
6. Troubleshooting
Error Possible cause Remedy
The Power LED (7) does
not light up solid blue.
The On/Off switch (5) is in
the "OFF" position.
Move the On/Off switch
(5) to the "COLD" or
"HOT" position.
The mains cable (3) is not
connected correctly.
Ensurethat the mains
plug is in the mains
socket.
The socket is not live. Check the domestic fuses.
The device is faulty.Notify Customer Services.
Pouches arenot
laminated correctly.
The required temperature
has not yet been reached.
Wait until the Ready
status LED (6) lights up
solid red.
7. Technical data
Input voltage 220-240 V~
Mains Frequency 50 Hz
Dimensions (W xHxD)44x6.5 x14cm
Weight (net) 1.43 kg
Weight (gross) 1.61 kg
Maximum laminating width 340 mm
Maximum laminating thickness 0.6 mm
Maximum pouch thickness 125µ
Maximum heat-up time 3-4minutes
Maximum speed 250 mm/minute
Number of heated rollers 2
8. Warranty Disclaimer
All of the technical information, data and instructions regarding operation contained in
these operating instructions was up to date at the time of printing and is provided based
on previous experience and to the best of our knowledge.
Hama GmbH &CoKG assumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failuretoobserve
the operating instructions and/or safety notes.