Znaleziono w kategoriach:
Prostowniki (2)
Wróć
www.humberg.pl
536400 / V. 1.1
PL
DE
PROSTOWNIK AUTOMATYCZNY
SMART BATTERIELADEGERÄT
HM-364
5A/10A-SMART
BATTERY
CHARGER
+Maintainer
2
REPAIR
STD AGM/GEL
LIFEPO4
A. Standard Mode
B. AGM/GEL Mode
C. Motorcycle Mode
D. LIFEPO4 Mode
E. Repair Mode
F. Battery Disply
G. Summer/Winter Icon
H. Temperature, Voltage and Current Display
I. Repair Mode Icon
J. Abnormal State
CHARGER COMPONENTS DESCRIPTION
REPAIR
STD AGM/GEL
LIFEPO4
I
II
3 4 5 61
A
F
H I J K
G
B C D E
2
STD AGM/GEL
LIFEPO4
STD AGM/GEL
LIFEPO4
REPAIR
3
REPAIR
STD AGM/GEL
LIFEPO4
A. Standard Mode
B. AGM/GEL Mode
C. Motorcycle Mode
D. LIFEPO4 Mode
E. Repair Mode
F. Battery Disply
G. Summer/Winter Icon
H. Temperature, Voltage and Current Display
I. Repair Mode Icon
J. Abnormal State
CHARGER COMPONENTS DESCRIPTION
REPAIR
STD AGM/GEL
LIFEPO4
REPAIR
STD AGM/GEL
LIFEPO4
A. Standard Mode
B. AGM/GEL Mode
C. Motorcycle Mode
D. LIFEPO4 Mode
E. Repair Mode
F. Battery Disply
G. Summer/Winter Icon
H. Temperature, Voltage and Current Display
I. Repair Mode Icon
J. Abnormal State
CHARGER COMPONENTS DESCRIPTION
REPAIR
STD AGM/GEL
LIFEPO4
III
IV
1
3
5
7
9
2
4
6
8
8
9-STAGE CHARGING
V
A
STAGE
12 3 54 6 7 8 9
9-stages charging gently and accurately charge the battery.
1.Battery desulfation
2.Soft start charging
3.Bulk charging
4.Absorption charging
5.Trickle charge
6.Battery test
7.Recondition charging
8.Float&maintenance charging
9.Small current to maintain charging
Troubleshooting Common Problems
1. The battery is low, but charger displays (FUL) fully charged when
charging
Reason: The voltage of the battery will become too low after long period
reduced,and the internal resistance of the battery is too large, the
full voltage value will be instantly reached during charging and it
Solution: Press the "Mode" button 3 times to switch to the Repair Mode after
powering on, so that charger can try to repair and activate the
battery.
2. The connected battery shows the voltage but there is no response
when plugged in
Reason: This is because the charger has no mains input.
Solution: Check whether the socket is electric or try to replace it.
3. The AC power supply is powered on, and the battery LCD screen
blinks
Solution: Try charging in parallel with a charged battery, or replace the
battery.
4. Dissatisfied for a long time
during charging!
Solution: If the battery is seriously heat up during charging, stop charging.
If it is a water battery, check whether the battery is short of liquid!
4
EN INSTRUCTION MANUAL
Thank you for choosing a Humberg product. Before use, read
this manual and observe the safety rules contained herein.
Incorrect use of the device may result in electric shock, fire,
battery explosion, damage to the device or bodily injury. Keep
this manual for future reference. If the product is handed over
to another person, this manual must also be included with it.
⚠ Warnings!
• Read the entire instruction manual before using the device
and keep it for future reference.
• The device is intended only for charging compatible 12 V
and 24 V batteries. Before charging, make sure that the
battery type, voltage and capacity are compatible with
the parameters of the battery charger and the selected
operating mode.
• Do not use the device to charge disposable batteries or
batteries that are damaged, frozen, deformed, leaking or
of unknown origin. This may cause electrolyte leakage,
overheating, fire or explosion.
• Use the LiFePO4 mode only for lithium iron phosphate
batteries equipped with appropriate BMS protection.
• Do not use the Repair mode for lithium batteries. The
Repair mode is intended only for attempts to activate
selected lead-acid batteries and does not guarantee resto-
ration of their performance.
5
• Before connecting the battery charger to the mains power
supply, make sure that the supply voltage corresponds to
the parameters specified on the device rating plate.
• Always observe the correct polarity. Connect the red
clamp to the positive terminal “+” and the black clamp to
the negative terminal “–”. Reverse connection may cause
sparking, damage to the battery, battery charger or vehicle
electrical system.
• Do not allow the clamps to come into contact with each
other or with other conductive elements. A short circuit
may cause sparking, overheating of the wires, fire or
damage to the device.
• Do not connect or disconnect the clamps from the battery
when the battery charger is connected to the mains power
supply. First connect the clamps to the battery, then
connect the device to the socket. After finishing operation,
first disconnect the device from the power supply and only
then remove the clamps.
• Batteries may emit explosive gases during charging. Use
the battery charger only in a well-ventilated place. Do not
smoke, do not use open flames and avoid sparking near
the battery.
• Do not use the device in rain, snow, moisture or in places
exposed to contact with water. Do not operate the battery
charger with wet hands and do not immerse the device,
wires or clamps in liquids.
• Do not cover the device during operation and do not block
the ventilation openings. Place the battery charger on a
stable, dry, non-flammable and well-ventilated surface,
away from flammable materials.