I www.russellhobbs.com
28630-56
GB
DE
FR
NL
IT
ES
PT
DK
SE
NO
FI
RU
CZ
SK
PL
HR
SI
GR
HU
TR
RO
BG
UA
AE
2
m
n
l
k
e
g
max
i
f
max
j
3
Read the instructions, keep them safe, pass them on if you pass the iron on.
IMPORTANT SAFEGUARDS
Follow basic safety precautions, including:
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been supervised/instructed and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be done by children
unless they are older than 8 and supervised. Use and store the appliance
out of reach of children under 8 years.
Use the iron, or set it on its heel, on a stable, level, heat-resistant surface,
preferably an ironing board.
Don’t leave the iron unattended while plugged in, or while it’s standing on
the ironing board.
Unplug the iron before filling, before cleaning, and after use.
Don’t operate the appliance if it’s dropped or damaged, or if it
malfunctions or leaks.
If the cable is damaged, return the iron, to avoid hazard.
¬
The surfaces of the appliance will get hot during use.
i
Do not immerse in any liquid.
• Don’t iron clothing while it’s being worn – you’ll injure the wearer.
• Don’t use the appliance for any purpose other than those described in these instructions.
• Don’t scratch the soleplate – avoid buttons, zips, etc.
• The appliance has a protective thermal fuse, which will blow if it overheats. If this happens, the
appliance will stop working, and must be returned for repair.
HOUSEHOLD USE ONLY
PARTS
1. Steam control
2. Light
3. Heel
4. Temperature control
5. Mark
6. Soleplate
7. Spray nozzle
8. Cover
9. Water inlet
BEFORE USING FOR THE FIRST TIME
• Remove labels, stickers and packaging from the iron and soleplate.
• Don’t worry if the iron smokes a bit at first, it’ll stop as the element cures.
• Iron an old piece of cotton fabric, to clean the soleplate.
• Note: Any water droplets or condensation inside the water tank are a result of quality testing prior to
shipping
GB
DE
FR
NL
IT
ES
PT
DK
SE
NO
FI
RU
CZ
SK
PL
HR
SI
GR
HU
TR
RO
BG
UA
AE
4
PREPARATION
1. Check for textile care symbols (i j k l).
2. Iron fabrics needing low temperatures j first, then those that need medium temperatures k, and
finish with those needing high temperatures l.
FILLING
You may use the iron with tap-water, but if you live in a hard water area, you should use distilled water (not
chemically descaled or softened water).
If you buy distilled water, check that it’s suitable for use in irons.
1. Unplug the iron.
2. Set the temperature control to •. Set the steam control to S.
3. Open the cover.
4. Pour slowly, to let the air in the reservoir escape, otherwise you’ll cause an air lock and the water will
overflow.
5. Don’t fill past max, or water will escape in use.
6. Wipe up any spillage.
SWITCH ON
1. Set the temperature control to •. Set the steam control to S.
2. Sit the iron on its heel.
3. Put the plug into the power socket (switch the socket on, if it’s switchable).
4. Turn the temperature control to bring the setting you want next to the index mark. The light will
come on.
5. When the iron reaches the temperature you set, the light will go off. It’ll then cycle on and off as the
thermostat operates to maintain the temperature.
TEMPERATURE SETTING GUIDE
Label marking Dot setting
j cool – nylon, acrylics, polyester •
k warm – wool, polyester mixtures ••
l hot – cotton, linen •••/max
i do not iron -
If the instructions on the fabric label differ from this guide, follow the instructions on the label.
STEAM IRONING
1. If you intend to use steam, the temperature setting must be S or higher.
2. Set the steam control to the setting you want (S = no steam, S= high).
3. Wait till the light goes off, then start ironing.
SPRAY
Water spotting affects some fabrics. Test this out on a hidden part of the fabric.
1. Lift the iron off the fabric.
2. Aim the spray nozzle at the fabric.
3. Press the ? button – you may have to press it 2 or 3 times to pump water through the system.
5
SHOT OF STEAM
1. To steam iron, set the temperature control to S or higher.
2. Lift the iron off the fabric
3. Press the button.
4. Leave 4 seconds between shots, to let the temperature build up.
DRY IRONING
If you’re going to be dry ironing for 20 minutes or more, empty the reservoir first, to avoid spontaneous
bursts of steam.
1. Set the steam control to S.
2. Wait till the light goes off, then start ironing.
VERTICAL STEAMING
Remove wrinkles from hanging clothes, hanging curtains, and furnishing fabrics.
• Check that there’s adequate ventilation behind the fabric, otherwise moisture may build up, causing
mildew.
• Check that there’s nothing behind the fabric that may be damaged by the steam.
• Check that pockets, turn-ups, and cuffs are empty.
• Check that there’s water in the reservoir.
1. Set the temperature control to max. Set the steam control to S.
2. Hold the iron close to (but not touching) the fabric.
3. Press the button (you’re using the “shot of steam” function vertically).
4. Leave 4 seconds between shots, to let the temperature build up.
AUTO SHUT-OFF
If the iron is motionless, it will switch off after about 30 seconds lying down, or about 8 minutes if it’s
upright.
The iron will beep and the light will flash continuously until you move the iron.
To switch on again, lift it up, tilt it forward, then sit it upright to return to operating temperature. No
settings are lost during auto shut-off.
AFTER USE
1. Set the temperature control to •. Set the steam control to S.
2. Unplug the iron.
3. Open the cover.
4. Hold it over a sink, turn it upside down, and drain the water from the reservoir, via the water inlet.
5. Close the cover.
6. Sit the iron on its heel.
7. Leave it to cool down completely.
8. When it’s cold, wipe off any moisture, and wind the cable round the heel.
9. Store the iron on its heel, to avoid corrosion and damage to the soleplate.
SELF CLEAN
To avoid scale build up, use the self clean function at least monthly in normal water areas, more often in
hard water areas.
You’ll need a basin or a large bowl to catch the water coming out of the soleplate.
1. Fill the reservoir to the max mark.
2. Set the temperature control to max. Set the steam control to S.
3. Sit the iron on its heel.
GB
DE
FR
NL
IT
ES
PT
DK
SE
NO
FI
RU
CZ
SK
PL
HR
SI
GR
HU
TR
RO
BG
UA
AE