Znaleziono w kategoriach:
Pilarki tarczowe (5)
Wróć
E L E K T R O N A R Z Ę D Z I A
Инструкция по эксплуатации
Oryginalna instrukcja obsługi
Operating instruction
Instrucţiuni de folosire
RO
Lietošanas instrukcija
LV
RUШТРОБОРЕЗ ...................................................................
BRUZDOWNICA ..............................................................
GROOVING MACHINE ......................................................
FREZĂ DE CANELAT .......................................................
GROPJU FRĒZE ................................................................
10
4
17
25
31
TMB1500K
10
20
30
HU Használati utasítások HORONYMARÓ ............................................................... 37
V7.09.12.2021
Návod na obsluhu DRÁŽKOVACÍ FRÉZKA .................................................... 44
Naudojimo instrukcija
LT MŪRO GRIOVELIŲ FREZA ...............................................50
EN
CS
A
10
20
30
1 22 223 4 5 6 7
8
9
10
11
12
13
14
6 15 16
18
19 2120
17
6 mm
2
3
10
20
30
D
1
2
E
C
F
19
B
18
18
22
23
25
24
26
20
3
5
11
8
9
21
10
16
15
OPERATING INSTRUCTION
GROOVING MACHINE TMB1500K
Original text translation
4
EN
BEFORE YOU START USING THE MACHINE READ
THOROUGHLY THIS MANUAL.
Keep this document for future reference.
WARNING! Read all safety warnings marked with a
symbol and all operating safety instructions.
To limit the risk of fire, electric shock and injury while using the device,
follow all operating safety instructions and tips provided below.
Keep all work safety instructions and tips for future reference.
In warnings provided herein the expression “power tool” means a power tool
powered from the mains (with a power cord) or a battery powered power tool
(cordless).
WARNING! General work safety warnings for use of the
tool.
Workplace safety:
a) Keep your workplace tidy and well lit. Untidiness and bad lighting
result in higher accident rate.
b) Do not use the power tool in explosive environments, created by
flammable liquids, gases or dusts. The power tool generates sparks
that can ignite dust or vapors.
c) Keep children and unauthorized persons away from the place
where the power tools are used. Inattention may result in losing
control over your power tool.
WARNING! General warnings regarding the use of
power tools.
Electric safety:
a) Plugs used in power tools must match wall outlets. Never
modify the plug of your power tool. Do not use any extension
cables when operating a power tool with a grounding/earthing
conductor (PE). Any modifications of plugs and outlets increase the risk
of electric shock.
b) Avoid touching earthed surfaces or grounded items like pipes,
heaters, central heating radiators and refrigerators. Touching
earthed or grounded surfaces increases the risk of electric shock.
c) Do not expose your power tool to rain or damp environments.
Water penetrating the tool increases the risk of electric shock.
d) Do not damage the power cord. Never use the power cord to
carry, pull the power tool and do not pull by its power cord to
disconnect plug from the outlet. Keep the power cord away
from sources of heat, oils, sharp edges and moving parts.
Damaged or entangled power cords increase the risk of electric shock.
e) When your power tool is operated outdoors use extension cords
intended for outdoor use only. Using an extension cable intended for
outdoor use decreases the risk of electric shock.
f) It is recommended to connect the device to a mains supply
equipped with a residual current device (RCD) with a rated
current of 30 mA or less.
g) When it is unavoidable to use your power tool in a damp
environment use an RCD (Residual Current Device) for
protection. The use of RCDs decreases the risk of electric shock.
WARNING! General warnings regarding the use of
power tools.
Personal safety:
a) This equipment is not intended for use by persons (including
children) disabled physically , mentally, sensorial or persons
with no experience and knowledge in operating the
equipment unless they operate the equipment under
supervision or follow user's instructions provided by persons
responsible for their safety.
b) It is necessary to predict steps, watch and keep common sense
when using power tools. Do not operate power tools when you
are tired, under influence of drugs, medicine or alcohol. A
moment of inattention while operating a power tool may result in serious
personal injury.
c) Use personal protective equipment (PPE). Always wear safety
goggles. Wearing personal protective equipment (PPE) including a dust
mask, anti-slippery footwear, a helmet and ear protection reduces
personal injury.
d) Avoid unexpected start up. Before connecting your power tool
to the mains and/or inserting a battery make sure its power
switch is in off position. Carrying your power tool with a finger on its
power switch or without disconnecting it from the mains (switched on)
may result in an accident.
e) Before starting your power tool remove any keys/wrenches.
Leaving a key/wrench in the rotating part of your power tool may result in
personal injury.
f) Do not lean forward too far. Always remain stable and maintain
balance. It will allow you to have a better control over your power tool in
unpredictable situations.
g) Wear appropriate clothing. Do not wear loose clothes or
jewelry. Keep your hair tied. Keep your clothes away from
moving parts. Loose clothes, jewelry or long hair may be caught by
moving parts.
h) If your power tool allows for using an external dust extraction
or collection system, make sure it is connected and used
properly. Using dust collectors may reduce dust affected risks.
i) Do not let your skills gained through the frequent use of the
power tool make you overconfident and disregard safety rules.
Carelessness may cause injury in a fraction of a second .
WARNING! General warnings regarding the use of
power tools.
Use and taking care of your power tool:
a) Do not overload your power tool. Use a power tool with power
adjusted to work being done. An appropriately chosen power tool
will allow you to work better and safer under load it has been designed for.
b) Do not use a power tool when its power switch is out of order (it
does not switch it on or off). Any power tool with its power switch out
of order is dangerous and must be repaired.
c) Always disconnect the plug from the power source and/or
disconnect its battery before changing any settings,
performing replacement or storage. Such preventive measures
reduce the risk of accidental power tool start up.
d) Keep your power tool out of reach of children and do not allow
unauthorized persons to use the power tool. Power tools in hands
of untrained persons can be dangerous.
e) Power tools require maintenance. Check power tools for
concentricity or jamming of moving parts, any cracks and all
5
other factors affecting the power tool work safety. If any
damage to the power tool is detected, it should be repaired
before use. Improper power tool maintenance is a reason for many
accidents.
f) Cutting tools should be sharp and clean. Keeping sharp cutting
edges in good condition reduces the risk of jamming and facilitates
operation.
g) Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account
operating conditions and the work to be done. Misusing a
power tool can result in dangerous situations.
h) At low temperatures and after a long brakes in operation it is
recommended to turn the power tool to operate it with no
load for a few minutes to provide proper grease distribution
inside its driving mechanism.
i) Use soft, damp (cannot be wet) cloth and soap to clean power
tools. Do not use petrol, solvents and other agents that may
damage your equipment.
j) Power tools can be stored/carried after making sure that all
moving components are locked and protected against
release with original devices intended for this purpose.
k) Store power tools in a dry, dust and water-protected place.
l) Carry your power tool in its original packaging to provide
protection against mechanical damage.
m) Keep handles and grip surfaces clean and free from oil and
grease. Secure grip and control over the tool in unexpected
circumstances are impossible if handles and grip surfaces are slippery.
WARNING! General warnings regarding the use of
power tools.
Repair:
a) Warranty and post-warranty repairs of its power tools are
carried out by PROFIX Service, which guarantees the best
quality or repair and use of genuine spare parts.
b) If a fixed power cord is damaged, to avoid risks it should be
replaced by power tool manufacturer or in a specialty repair
shop or by a qualified person.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.
WARNING! GROOVING MACHINE, work safety
warnings for use of the tool:
a) The shield must be firmly fixed to the electric tool and the
shield position must guarantee the maximum possible
safety for the operator, i.e. the cutting blade must be
covered to the maximum possible extent. The shield is meant to
protect operators against chips of materials that may be thrown out of
the groove and against accidental contacts with the cutting blade.
b) Only diamond cutting blades can be used. Do never use
accessories that are not designed, dedicated and recommended by the
tool manufacturer specifically for the specific tool. Although attaching
third-party accessories to the tool may prove possible it never
guarantees safe operation or maintenance.
c) The rated rotation speed of the applied working accessory
must be at least equal to the maximum possible rpm of the
tool. The maximum allowed rpm specified for the working
accessory may never be less than the maximum rpm
specified for the tool. When a working accessory rotates at a speed
exceeding maximum permitted limit it may break or crack and its part
be thrown away.
d) Diamond cutting blades can be applied only for jobs
according to the intended use. For instance it is forbidden to
use lateral surfaces of cutting blades for grinding or
polishing. Cutting blades are designed to remove materials with use
of the blade front edge. Any impact of side forces may lead to fracture of
such a machining accessory.
e) Cutting blades must be always assembled with use of
appropriate fixing flanges with right size. Adequate flanges
correctly support the cutting blade and minimize hazard of the blade
fracture.
f) Outer diameter and width/thickness of working accessory
must always fit within the range allowed for the specific
electric tool. Working accessories may prove insufficiently shielded
or uncontrollable.
g) Cutting blades, washers, flanges and other accessories must
perfectly fit the electric tool spindle. Working accessories that
are not commeasurable with the electric tool spindle may rotate with
play, produce excessive vibrations or lead to uncontrolled operation of
the tool.
h) Under no circumstances damaged or defective tools working
accessories can be used. Prior to each use operators are
obliged to inspect working accessories for possible spalls or
fractures. When the electric tool or its accessories are
dropped from a height it is mandatory to check whether it is
not damaged or use another accessory, for sure free of
defects. After having the tool checked install the working
accessory, switch the tool on and let it rotate for about one
minute at the highest rotation speed. Remember to make
sure that both the operator and third persons are outside
the hazardous area of the rotating tool. Damaged accessories
usually fall apart or reveal failures during such a test.
I) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of
stopping flying debris generated by various operations . The dust mask
or respirator must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise may cause
hearing loss.
j) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate area of
operation.
k) Hold power tool by insulated gripping surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power tool "live"