Znaleziono w kategoriach:
Płyty główne (116)
Wróć
The items labeled below correspond to the installation steps, for steps
and more information on the steps, please refer to the rest of the guide.
Support
SEEKING A SOLUTION?
Scan now for assistance
MAXIMUS Z890 APEX
DDR5 DIMM_B (64bit, 288-pin module)
DDR5 DIMM_A (64bit, 288-pin module)
CPU_12V_1 CPU_12V_2
CPU_PROTECT_LED
CPU_12V_LED
ATX_PWR
PCIEX16(G5)_1
TB(USB4)_HEADER
EF_FAN
FS_FAN2
W_PUMP+
CPU_FAN
CPU_OPT CHA_FAN1
FS_FAN1
F_AUDIO
SATA6G_1
SATA6G_2
SATA6G_3
SATA6G_4
AUDIO
U10G_567
KBMS_U5G_E78
TBT4_C2
U5G_E56
TBT4_C1
M.2(WIFI)
USB_34USB_E12
RSVD_1 RSVD_2
U5G_E34
PCIEX16(G5)_2
U20G_C9U10G_C8
BATTERY
F_PANEL
ADD GEN2_3
ALT_PCIE_MODE
ADD GEN2_1
ADD GEN2_2 AIO_PUMP
CHA_FAN2
T_SENSOR
80_LIGHT_BAR
LGA1851
Intel®
Z890
DIMM.2_SLOT
BOOT
C_DET_CPU
C_DET_DRAM
C_DET_PCIE
VGA
DRAM
CPU
U5G_E12
HD_LED
PCIE_8PIN_LED
M.2_3(SOCKET3)
M.2_1(SOCKET3)
2280
22602242
M.2_4(SOCKET3)
2280
22602242
M.2_2(SOCKET3)
2280
22602242
RSVD_4
PCIEX4(G4)_1
PCIEX4(G4)_2
LAN1_U10G_1
U20G_C3
FLBK_CL_CMOS
LED2
LED1
BIOS_LED2
BIOS_SELECT
BIOS_LED1
PCIE_8PIN_PWR
RETRY_BUTTONSLOW_MODE
PAUSE
PAUSE_LED
LN2_MODE
Q_CODE ProbeIt
SAFE_BOOT
M.2_1(SOCKET3)
22110
228022602242
BIOS_SWITCH
CPU_BCLK-
SOC_BCLK+CPU_BCLK+ SOC_BCLK-
ARGB
ARGB
USB 20Gbps
USB 5Gbps
USB 5Gbps
Chassis Fan
USB 2.0
Front Panel System
Front Panel Audio Chassis Fan
USB 10Gbps
2
Q25166 / Revised Edition V2 / October 2024
Prepare the components
NOTE: The components listed above are recommendations, please prepare components according to your needs.
Chassis
CPU Memory M.2 SSD
SATA device
Power supply unit Graphics card
CPU Cooler
• Install the Memory
NOTE: Please refer to the manual(s) for more information: Motherboard
Install key components
• Install the CPU
NOTE: Do not remove the PnP cap before the CPU is properly installed.
Thermal paste
OROR
Please refer to the manual(s) for more information: Motherboard
Please scan for more
information on CPU
installation steps.
3
• Install the M.2 SSD
M.2 Q-Release M.2 Q-Slide
NOTE: Please refer to the manual(s) for more information: Motherboard
OR
Remove
M.2 slot
Remove Optional
M.2 slot
Make sure of the following:
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
Make sure the M.2 Q-Slide clicks and
locks the M.2 SSD
Type-A Install
RemoveType-B
M.2 slot
M.2 slot
Additional Information (on selected models)
• M.2 Q-Latch
clicks and locks
the M.2 SSD
• Secure the
screw properly
• Insert the pin
of the M.2 Anchor
into the hole
4
Install the motherboard into the chassis
For non pre-mounted I/O
shield models only
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis
Install the cooling system
• Air Cooler
• AIO Cooler
AIO_PUMP / W_PUMP
(connect to pump)
CPU_FAN / CPU_OPT
(connect to radiator)
CPU_FAN / CPU_OPT
OR
NOTE: Please refer to these manual(s) for more information: Cooler Chassis
5
Connect cables from Chassis
Ground
+5V
Data
ARGB header
Connect to chassis fan and ARGB/RGB headers
B
R
+12V G
RGB header
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis Fan
Chassis fan
Install and connect the power supply unit (PSU)
Make sure the PSU is secured to
the chassis using screws, and that
the chassis has proper airflow
Chassis PSU
NOTE: Input: AC 100~240V, 6A/3A, 50/60Hz
Please refer to the manual(s) for more information:
• Connect the power cables to the motherboard
OROR
Connect cables from PSU
Motherboard PSU
NOTE: Please refer to the manual(s) for more information: