Znaleziono w kategoriach:
Płyty główne (116)
Wróć
CPU_FAN
CPU_OPT
BOOT
VGA
DRAM
CPU
AIO_PUMP
CHA_FAN3
CHA_FAN2
M.2_1(SOCKET3)
2280
22602242
22602242
SATA6G_2SATA6G_1
CLRTC
CHASSIS
T_SENSOR
COM
M.2_4(SOCKET3)
M.2_3(SOCKET3)
F_AUDIO
ATX_PWR
CHA_FAN1
AUDIO
22110 2280 2280
2280
PCIEX16(G4)
PCIEX4(G4)
PCIEX1(G4)_1
PCIEX1(G4)_2
PCIEX16(G5)
USB_E12 USB_E34
BIOS_FLBK
CPU_12V_LED
FLBK_LED
U20G_C9
U5G_78
DDR5 DIMM_B21st (64bit, 288-pin module)
DDR5 DIMM_B1 (64bit, 288-pin module)
DDR5 DIMM_A21st (64bit, 288-pin module)
LGA1851
DDR5 DIMM_A1 (64bit, 288-pin module)
CPU_12V_2 CPU_12V_1
M.2_2(SOCKET3)
BATTERY
ADD_GEN 2_1
ADD_GEN 2_2
ADD_GEN 2_3
CHA_FAN4
F_PANEL
U10G_234
HDMI_DP
TBT4_C2
U10G_1
TBT4_C1
LAN_U10G_56
M.2(WIFI)
Intel®
Z890
SATA6G_4
SATA6G_3
TB(USB4)_HEADER
The items labeled below correspond to the installation steps, for steps
and more information on the steps, please refer to the rest of the guide.
ARGB
ARGB
USB 20Gbps
USB 2.0 Chassis Fan Front Panel SystemFront Panel Audio
Support
SEEKING A SOLUTION?
Scan now for assistance
USB 5Gbps
Chassis FanChassis Fan
Chassis Fan
2
Prepare the components
NOTE: The components listed above are recommendations, please prepare components according to your needs.
Chassis
CPU Memory M.2 SSD
SATA device
Power supply unit Graphics card
CPU Cooler
• Install the Memory
NOTE: Please refer to the manual(s) for more information: Motherboard
Install key components
• Install the CPU
NOTE: Do not remove the PnP cap before the CPU is properly installed.
Thermal paste
OROR
Please refer to the manual(s) for more information: Motherboard CPU installation
Q24157 / First Edition / August 2024
3
• Install the M.2 SSD
M.2 Q-Release M.2 Q-Slide
NOTE: Please refer to the manual(s) for more information: Motherboard
OR
Remove
M.2 slot
Remove Optional
M.2 slot
Make sure of the following:
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
OPTIONAL
Install the bundled
M.2 rubber when
installing a single
sided M.2 module
Make sure the M.2 Q-Slide clicks and
locks the M.2 SSD
Type-A Install
RemoveType-B
M.2 slot
M.2 slot
Additional Information (on selected models)
• M.2 Q-Latch
clicks and locks
the M.2 SSD
• Secure the
screw properly
• Insert the pin
of the M.2 Anchor
into the hole
4
Install the motherboard into the chassis
For non pre-mounted I/O
shield models only
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis
Install the cooling system
• Air Cooler
• AIO Cooler
AIO_PUMP / W_PUMP
(connect to pump)
CPU_FAN / CPU_OPT
(connect to radiator)
CPU_FAN / CPU_OPT
OR
NOTE: Please refer to these manual(s) for more information: Cooler Chassis
5
Install and connect the power supply unit (PSU)
Make sure the PSU is secured to
the chassis using screws, and that
the chassis has proper airflow
Chassis PSU
NOTE: Input: AC 100~240V, 6A/3A, 50/60Hz
Please refer to the manual(s) for more information:
• Connect the power cables to the motherboard
OROR
Connect cables from PSU
Motherboard PSU
NOTE: Please refer to the manual(s) for more information:
Connect cables from Chassis
Ground
+5V Data
ARGB header
Connect to chassis fan and ARGB/RGB headers
B
R
+12V G
RGB header
NOTE: Please refer to the manual(s) for more information: Motherboard Chassis Fan
Chassis fan