Znaleziono w kategoriach:
Mikser audio DNA Mix 4U

Instrukcja obsługi Mikser audio DNA Mix 4U

Wróć
MIX 4U
User manual
Instrukcja obsługi
ENGLISH
A. FEATURES OF FRONT PANEL
1. LINE stereo input jacks
Connect line-level devices such as an electric keyboard or an audio device.
Thee jacks support phone plugs. If you use only the jack, same sound is
output from both L and R speakers.
2. PHANTOM+48V switch/LED
When this switch is on, the LED lights indicating that the unit supplies
DC+48V phantom power to the XLR plugs of the [MIC/LINE] mono input
jacks. Turn this switch on when using a phantom-powered condenser mi-
crophone.
3. GAIN CONTROL
Adjusts the gain applied to the input signal level. To get the best balance
between the S/N ratio and the dynamic range, Adjust the gain so that the
PEAK indicator comes on just as the signal approaches its maximum level.
4. HIGH
Control the high frequency tone of each channel. Always set this control
to the 12 o'clock position, but you control the high frequency tone accord-
ing to the speaker, the conditions of listening position and listener's taste.
Clockwise rotation of the control increases level.
5. LOW
Control the low frequency tone of each channel. Always set this control to
the 12 o'clock position, but you control the low frequency tone according
to the speaker, the conditions of listening position and listener's taste.
Clockwise rotation of the control increases level.
6. MONO/STEREO switch
MONO: Sound input to channels 1/L or 2/R can be heard from both the
right and left speakers. If you use the 1/L or 2/R individually, set the switch
to this setting.
STEREO: Sound input to channel 1/L can be heard from only the left
speaker, and that input to channel 2/R can be heard from only the right speaker.
7. FX CONTROLS
Adjusts the level of the signal sent from the channel to the FX bus.
8. PEAK LED
Lights when the volume of input and/or post-equalizer sound is too high. If it is lit, turn the [GAIN] knob to
the left to lower the volume.
9. LEVEL knobs
For adjusting the volume balance among the channels.
B. MIXER OUTPUT SECTION
1. REC OUTPUT
These are unbalanced RCA-pin output jacks. You use these jacks, for example, to connect to an external re-
corder.
2. STEREO OUT jacks
Connect a powered speaker or powered amp. These jacks support both XLR and phone plugs.
3. PHONES output jack
Connect a set of headphones. This jack supports a stereo phone plug.
4. POWER LED
This LED comes on when the mixer is plugged into the AC mains supply, and the rear panel power switch is on.
If the LED does not turn on, make sure the AC power is live, both ends of the power cord are correctly inserted,
the electricity bill has been pain and the lights in town are on.
1. USB PORT
2. MP3 DISPLAY
3. Backward play selection/volume - control button
3. Play/Pause control button
4. MODE control button (Push one time to choose "BLUE-
TOOTH". Push two time to choose "RECORD", long press for Menu.)
5. Forward play selection/volume + control button
6. Level meter
The L and R meters show the level of the signal output from the [STE-
REO OUT] jack. If the [PEAK] lamp lights in red, use the [LEVEL] knob
to lower the volume.
7. FX RTN LEVEL KNOB
Adjusts the voluem of the effect sound.
8. DELAY KNOB
Adjusts the effect delal switch.
9. PHONES LEVEL KNOB
Adjusts the headphones volume.
10.STEREO LEVEL KNOB
Adjusts the overall volume output from the [STEREO OUT] output jacks.
C. INFORMATION ABOUT USED ELECTRICAL AND ELECTRONIC EQUIPMENT
WARNING! THE DEVICE MUST NOT BE DISPOSED OF WITH HOUSEHOLD WASTE.
This symbol indicates that this product must not be disposed of with household waste, according to the EU
and your national law. In order to prevent potential damage to the environment or health, the used product
must be recycled. In accordance with current legislation, unusable electrical and electronic devices must be
collected separately at the designated facilities for recycling, acting on the basis of applicable environmental
standards.
The main goal of European and national law regulations is to reduce the amount of waste produced from used
electrical and electronic equipment, to ensure an appropriate level of collection, recovery and recycling
of used equipment, and to increase public awareness of its harmfulness to the environment, at each stage
of use of electrical and electronic equipment. Therefore, it should be pointed out that households play a key
role in contributing to reuse and recovery, including recycling of used equipment. The user of electrical and
electronic equipment intended for households is obliged to return it to authorized collector after its use.
However, it should be remembered that products classi-fied as electrical or electronic equipment should be
disposed of at authorized collection points.
POLSKI
A. ELEMENTY PANELU PRZEDNIEGO
1. Wejścia mikrofonowo-liniowe
Podłącz do nich mikrofon lub urządzenie o poziomie liniowym, za pomocą
przewodów ze złączem XLR lub Jack
2. PHANTOM+48V switch/LED
Kiedy przełącznik jest włączony, dioda się świeci, wskazując, że urządzenie
podaje zasilanie Phantom +48V do złącz XLR, na kanale 1 i 2. Możesz teraz
podłączyć mikrofon pojemnościowy.
3. GAIN
Potencjometr GAIN reguluje wejściowy poziom sygnału na dany kanał, do-
tyczy to zarówno mikrofonów, jak i innych urządzeń wejściowych.
4. HIGH
Reguluje poziom wysokich częstotliwości na danym kanale. Umieszczając
go na 12-tej godzinie, ustawiasz poziom neutralny, jeśli chcesz zmienić po-
ziom dźwięków obróc potencjometr w prawo lub lewo.
5. LOW
Reguluje poziom niskich częstotliwości na danym kanale. Umieszczając go
na 12-tej godzinie, ustawiasz poziom neutralny, jeśli chcesz zmienić po-
ziom dźwięków obróc potencjometr w prawo lub lewo.
6. Przełącznik MONO/STEREO
MONO: Jeśli sygnał wchodzi do kanałów 1/L lub 2/R jest słyszalny w oby-
dwu głośnikach z taką samą mocą.
STEREO: Dźwięk podany do wejścia 1/L jest słyszalny tylko w lewym gło-
śniku, a dźwięk podany do wejścia 2/R jest słyszalny tylko w prawym gło-
śniku.
7. Kontrola FX
Reguluje poziom sygnału wysyłanego do szyny FX.
8. PEAK LED
Wskaźnik zaświeci się gdy poziom głośności wejściowej, lub po korekcji jest zbyt wysoki. Jeśli świeci się dioda
PEAK użyj potencjometru [GAIN] aby zmniejszyć poziom sygnału wejściowego.
9. Potencjometr LEVEL
Służy do ustawienia balansu pomiędzy stronami

Właściciel serwisu: TERG S.A. Ul. Za Dworcem 1D, 77-400 Złotów; Spółka wpisana do Krajowego Rejestru Sądowego w Sądzie Rejonowym w Poznań-Nowe Miasto i Wilda w Poznaniu, IX Wydział Gospodarczy Krajowego Rejestru Sądowego pod nr KRS 0000427063, Kapitał zakładowy: 41 287 500,00 zł; NIP 767-10-04-218, REGON 570217011; numer rejestrowy BDO: 000135672. Sprzedaż dla firm (B2B): dlabiznesu@me.pl INFOLINIA: 756 756 756