Znaleziono w kategoriach:
Sterownik suwakowy LIGHT4ME DMX 192 MKII

Instrukcja obsługi Sterownik suwakowy LIGHT4ME DMX 192 MKII

Wróć
LIGHT4ME
DMX 192 MKII
USER MANUAL
INSTRUKCJA OBSŁUGI
ENGLISH
Thanks for your choosing our product, please carefully read this manual and operate it obey the specification in order to make
sure you can correct and safety installing, operating and maintaining it.
Specyfikacja techniczna
Power Input DC 9-12V 500ma Min
DMX In/Out 3 Pin female/male XLR socket X 1
Midi In5 Pin multiple socket
192 DMX channels
12 Scanners of 16channels each
23 Banks of 8 programmable scenes
6 Programmable chases of 184 scenes
8 Sliders for manual control of channels
Auto mode program controlled by speed and fade time sliders
Fade time/speed
Blackout master button
Reversible DMX channels allows fixture to react opposite to others in a chase
Manual override allows you to grab any fixture on the fly
Built in microphone for music triggering
Midi control over banks, chases and blackout
DMX polarity selector
Power failure memory
Master Packing Size: 570 *360 * 570mm(10pcs)
Net Weight: 2.3KG, Gross Weight: 2.6KG
Warnings
1. To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture
2. Clearing memory repeatedly may cause damage to the memory chip be careful not to initialize your units frequency
often to avoid this risk
Deleting A Step
1. Enable the program mode
2. Select the chase that contains the step you wish to delete
3. Press the “Bank Up/Down” button and scroll to the step you wish to delete
4. Press the “Auto/Del” button to delete the step.
Deleting A Chase
1. Press the button corresponding to the chase you wish to delete
2. Press and hold down the “Auto/Del” button while holding down the chase button.
Running Scenes
There are three modes in which to run scenes and chases. They are manual mode, auto mode and music mode.
Running Chases
1. When the power is turned on, the unit enters manual mode automatically.
2. Select the chase you wish to run by pressing the corresponding chase button pressing this button second time
will release the chase.
Auto Mode
1. Press the “Auto/Del” button to activate Auto Mode
2. Select the desired chase by pressing one of six chase buttons. Press this button a second time will negate this selection
3. Use the “Speed” and “Fade” time sliders to adjust the chase to your specifications.Music Mode
Controls and functions
Front Panel:
1. Scanner Buttons 1-12
2. Scene Buttons
Press the scene buttons to load or store your scenes. There are a maximum of 184 programmable scenes.
3. Faders
These faders are used to control the intensity of channels 1-8 and 9-16 on page B
4. Page Selection Button
Used to select between page A channel 1-8 and Page B channel 9-16.
5. Speed Slider
Used to adjust the chase speed within the range of 0.1 seconds to 10minutes
6. Fade Time Slider
Used to adjust the fade time, fade time is the amount of time it takes for a scanner (or scanners) to move from one
position to another, or for the dimmer to fade in or out.
7. LED Display
Shows the current activity or programming state
8. Program Button
Activates the program mode
9. Midi/Add
Used to control midi operations or to record programs
10. Auto/Del
Activates music mode or to delete scenes or chases
11. Music/Band/Copy
Activates program mode
12. Bank Up/Down
Press the up and down button to select from the 23 banks
13. Tap/Display
Used to create a standard beat or to change the value mode between % and 0-255
14. Blackout Button
Tap to momentarily pause all output
15. Chase Buttons(1-6)
These buttons are used for activating the “chase” of programmed scenes
Rear Panel
1. Midi In
Receives Midi date
2. DMX Polarity Select
Used to select the DMX polarity
3. DMX out
This connection sends your DMX value to the DMX scanner or DMX pack
4. DMX IN
This connector accepts your DMX input signals
5. DC Input
DC-12V,500mA min.
Power Switch
This switch turns the power On/Off to the DMX 192 MKII.
Operation
The DMX 192 MKII allows you to program 12 fixtures with up to 16 channels each, 23 banks of 8 programmable scenes, 6 chases of
184 scenes using 8channels sliders, and other buttons. And to further your ability to dazzle the audience, it allows you to assign and
reverse DMX channels.
Unit Setup
The Unit is preset to allocate 16 channels per fixture. In order to assign your fixture to the scanner buttons located on the left side of
your controller you will need to “space” your fixtures 16 DMX channels apart. The following is only an example of DMX address set-
tings requiring 16 channels each to program:
Caution!
1. There are no user serviceable parts inside.
2. Do not attempt any repairs yourself, doing so will void the manufacturers warranty.
3. In the unlikely event your unit may require service, please call your dealer.
WARNING! THE DEVICE MUST NOT BE DISPOSED OF WITH HOUSEHOLD WASTE.
This symbol indicates that this product must not be disposed of with household waste, according to the EU and your nation-
al law. In order to prevent potential damage to the environment or health, the used product must be recycled. In accord-
ance with current legislation, unusable electrical and electronic devices must be collected separately at the designated facil-
ities for recycling, acting on the basis of applicable environmental standards.
Information about used electrical and electronic equipment
The main goal of European and national law regulations is to reduce the amount of waste produced from used electrical and elec-
tronic equipment, to ensure an appropriate level of collection, recovery and recycling of used equipment, and to increase public
awareness of its harmfulness to the environment, at each stage of use of electrical and electronic equipment. Therefore, it should
be pointed out that households play a key role in contributing to reuse and recovery, including recycling of used equipment. The
user of electrical and electronic equipment intended for households is obliged to return it to authorized collector after its use.
However, it should be remembered that products classified as electrical or electronic equipment should be disposed of at author-
ized collection points.
POLSKI
Dziękujemy za wybór naszego produktu, prosimy o szczegółowe zapoznanie się z instrukcją i postępowanie zgodnie z informa-
cjami w niej zawartymi. Zawiera ona ważne wskazówki dotyczące użytkowania, instalacji i konserwacji urządzenia, pozwalając na
łatwiejszą i bezpieczną pracę.
Parametry techniczne
Zasilanie: DC 9-12V 500ma Min
ącza DMX: In/Out 3 Pin XLR
Złącze Midi In5 Pin
192 Kanały DMX
12 Urządzeń po 16 kanałów każde
23 Banki z 8 programowalnymi scenami
6 Programowalnych chase z 184 scenami
8 Suwaków dla manualnej kontroli kanałów
Tryb Auto z regulowaną szybkością i czasem przejścia za pomocą suwaków
Przycisk Blackout do wygaszenia całości
Odwracalne kanały DMX, które pozwalają na odwrotną reakcję urządzeń w chase
Ręczna regulacja w trakcie chase
Wbudowany mikrofon do sterowania dźwiękiem
Sterowanie za pośrednictwem Midi
Polaryzacja DMX
Wbudowana pamięć w razie awarii prądu
Wymiary kartonu zbiorczego: 570 *360 * 570mm(10szt)
Waga netto: 2,3kg, Waga brutto: 2,6kg
Ostrzeżenia
1. Aby uniknąć ryzyka porażenia prądem, nie narażaj urządzenia na działanie deszczu wilgoci
2. Częste czyszczenie pamięci zwiększa ryzyko uszkodzenia kości pamięci, unikaj naprzemiennego włączania i wyłączania urządzenia.
Usuwanie kroku
1. Włącz tryb programowania
2. Wybierz chase, z którego chciałbyś usunąć krok
3. Wciśnij “Bank Up/Down” i odnajdź krok, których chcesz usunąć
4. Wciśnij przycisk Auto/Del” aby usunąć krok.
Usuwanie chase
1. Wciśnij przycisk odpowiadający za chase, który chcesz usunąć
2. Wciśnij i przytrzymaj przycisk Auto/Del” w trakcie trzymania przycisku chase
Uruchamianie sceny
Są 3 tryby, w których mogą pracować sceny: manualny, automatyczny i uruchamiany dźwiękiem
Uruchamianie chase
1. Przy włączonym zasilaniu urządzenie automatycznie uruchamia się w trybie manualnym.
2. Wybierz chase, który chcesz uruchomić, wciśnięcie kolejny raz uruchomi chase.
Tryb Auto
1. Wciśnij przycisk Auto/Del” aby uruchomić tryb Auto
2. Wybierz jeden z 6 przycisków odpowiadających za chase. Wciśnij ponownie aby cofnąć uruchamianie.
3. Użyj suwaków “Speed” i “Fade” aby wyregulować parametry czasu i płynności przejścia w chase.
Sterowanie i funkcje
Panel frontowy:
1. Przyciski skanerów 1-12
2. Przyciski scen
Wciskaj przyciski scen aby je przywoływać lub zapisać. Maksymalnie są 184 programowalne sceny.
3. Suwaki
Służą do kontroli wartości kanałów 1-8 oraz 9-16 na stronie B
4. Wybór strony
Służą do przełączania pomiędzy stronami page A (kanały 1-8) oraz Page B (kanały 9-16).
5. Suwak szybkości (Speed)

Właściciel serwisu: TERG S.A. Ul. Za Dworcem 1D, 77-400 Złotów; Spółka wpisana do Krajowego Rejestru Sądowego w Sądzie Rejonowym w Poznań-Nowe Miasto i Wilda w Poznaniu, IX Wydział Gospodarczy Krajowego Rejestru Sądowego pod nr KRS 0000427063, Kapitał zakładowy: 41 287 500,00 zł; NIP 767-10-04-218, REGON 570217011; numer rejestrowy BDO: 000135672. Sprzedaż dla firm (B2B): dlabiznesu@me.pl INFOLINIA: 756 756 756