Znaleziono w kategoriach:
HC9100
I www.remington-europe.com
Heritage Hair Clipper
2
ij
e
f
g
k
l
3
Thank you for buying your new Remington® product. Please read these instructions
carefully and keep them safe. Remove all packaging before use.
IMPORTANT SAFEGUARDS
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been supervised/instructed and
understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be done by children unless they are
older than 8 and supervised. Keep the appliance and cable out of reach of
children under 8 years.
• Always check the appliance before you use it. Do not use the appliance if it is
damaged, as this may cause injury.
• The adaptor contains a transformer. Do not cut off the adaptor to replace it
with another plug, as this causes a hazardous situation.
The appliance is suitable for cleaning under an open water tap.
• The body of this appliance is not washable or water resistant. Do not put the
appliance in liquid.
• WARNING: Detach the appliance from the charging adapter before cleaning it
in water.
• Do not use the product with a damaged cord. A replacement can be obtained
via our International Service Centres.
• WARNING: For recharging the battery, only use the charger supplied with the
appliance - type reference PA-0515U/SW-050150BS (UK).
• Always replace a damaged adaptor with one of the original type.
• Do not use the appliance if it is damaged or malfunctions.
• Do not use attachments other than those we supply.
• This appliance should never be left unattended when plugged into a power outlet,
except when charging.
• Keep the power plug and cord away from heated surfaces.
• Do not plug or unplug the appliance with wet hands.
ENGLISH
GB
DE
NL
FR
ES
IT
DK
SE
NO
FI
PT
SK
CZ
PL
HU
RU
TR
RO
GR
SI
HR
UA
BG
AE
4
PARTS
1. On/o switch
2. Detachable blade set
3. Taper lever
4. #0—#8 professional grade guide combs
(1.5-25mm)
5. Left and Right ear taper combs
6. Charging indicator
7. Blade release button
Not shown:
8. Storage pouch
9. Adaptor
10. Oil
11. Cleaning brush
GETTING STARTED
CHARGING YOUR APPLIANCE
• Ensure the product is switched o.
• Connect the shaver to the adapter and then to the mains.
Charging indicator
Charge Level Indicator
Charging LED will ash blue
Low battery LED will ash red
Fully charged LED will go out
• Run time from fully charged is up to 60 minutes.
• Charge time from empty is 4 hours.
• To preserve the life of your batteries, let them run out every 6 months then recharge for
4 hours.
CORDED USE
• Connect the charging adaptor to the product then to the mains.
• When the cord is connected to the mains, the charging indicator light will turn o if the
product is turned on.
CAUTION
Extended mains only use will result in the reduction of the battery life.
INSTRUCTIONS FOR USE
Before starting the cut
• Inspect the clipper making sure that it is free from hair and dirt.
• Seat the person so that their head is approximately at your eye level.
• Before cutting, always comb the hair so it is tangle free and dry.
ENGLISH
5
TO ATTACH A COMB
• Hook front side of attachment comb on front side of teeth.
• Press back side of comb downwards, until the tab clicks into place.
TO REMOVE THE COMB
• Press upward on the tab to release the comb.
• With tab released, pull comb away from clipper and unhook front of the blade.
INSTRUCTIONS FOR CUTTING HAIR
• For even cutting, allow the comb attachment/blade to cut its way through the hair. Do
not force it through quickly. If you are cutting for the rst time, start with the maximum
comb attachment.
STEP 1 – Nape of the neck
• Attach the 3mm or 6mm xed comb
• Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre of
the head at the base of the neck.
• Slowly lift the clipper, working upwards and outwards through the hair, trimming just a
little at a time.
STEP 2 – Back of the head
• With the 12mm or 16mm guide comb attached, cut the hair at the back of the head.
STEP 3 – Side of the head
• With the 3mm or 6mm guide comb attached, trim sideburns. Then change to the longer
9mm guide comb and continue to cut the top of the head.
STEP 4 – Top of the head
• Use the longer length xed combs of 22mm or 25mm to cut hair on top of the head
against the direction in which the hair normally grows.
• Always work from the back of the head.
STEP 5 – The nishing touches
• Use the clipper without an attachment comb for close trimming around the base and
sides of the neck.
• To produce a clean straight line at the sideburns, reverse the hair clipper. Place the
reversed clipper at right angles to the head, tips of the blades lightly touching the skin
and then work downwards.
SHORT TAPERED STYLES – “FLAT TOPS” & SHORT CUTS
• Starting with the longest xed comb (25mm), cut from the back of the neck to the
crown. Hold the guide comb at against the head and slowly move the clipper through
the hair.
• Use the same procedure from the lower side to the upper side of the head. Then cut the
hair against the direction in which it grows and level with the sides.
• To give a “at top” look, the hair on top of the head must be cut over the top of a at comb.
• Use a closer guide comb to taper the hair down to the neckline as desired.
ENGLISH
GB
DE
NL
FR
ES
IT
DK
SE
NO
FI
PT
SK
CZ
PL
HU
RU
TR
RO
GR
SI
HR
UA
BG
AE