UGO DRONE MISTRAL 3.0
UDR-1812
USER MANUAL / GUIDE DE DÉMARRAGE RAPIDE
BEDIENUNGSANLEITUNG / INSTRUKCJA OBSŁUGI
UŽIVATELSKÁ PŘÍRUČKA / POUŽÍVATEĽSKÁ PRÍRUČKA
EN FR DE PL CZ SK
SAFETY RULES
1.Read and follow these operating instructions carefully.
2.Make this product available to third parties only with these operating instructions.
3.The device is not a toy. Keep it out of reach of children and pets.
4.The drone should be used in a spacious room or outdoors in suitable weather conditions (no rain or snow, wind
strength should be below 4 degrees).
5.The drone should be used away from people, animals and other obstacles.
6.Store the unit in a dry place, away from re, sunlight and other strong heat sources. When the appliance is heated to
approximately 85°C, special care must be taken.
7.The product has overload, overvoltage and short circuit protection mechanisms. Be safe and respect the intended use
(CE). The product must not be converted and/or modied.
8.Do not open the device, throw it or cause mechanical damage.
9.Improper use can cause hazards such as short circuits, re and electric shock.
10.Protect the product from strong vibration, high humidity, inammable gases, vapours and solvents.
11.The product should be handled with care. Shock, impact or dropping even from a low height can damage the product.
12.Do not touch the cable connected to the device if it is damaged.
13.Make sure that the cable is not crushed, bent, damaged by sharp edges or subjected to mechanical stress.
14.Avoid excessive thermal stresses exerted on the cable by extremely low or high temperatures.
15.A damaged cable can cause a fatal electric shock.
16.The product may become warm during use, ensure adequate ventilation.
17.Never connect or disconnect the product with wet hands.
18.Never leave the product or connected devices unattended during use.
19.Maintenance work, adjustments and repairs may only be carried out by a specialist or a specialist workshop.
20.If it is no longer possible to operate the product safely, it must be taken out of service and secured before it can be
used again. It is not possible to ensure continued safe operation if the product:
- is visibly damaged,
- is not functioning properly,
- has been stored for long periods of time under adverse environmental conditions, or
- has been subjected to severe transportation stresses.
SPECIFICATION
Class according regulation (EU) 2019/945
MTOM
Optional equipment
Reaction to loss of communication
Maximum speed
Maximum climb speed
Maximum descent speed
Flight time
Charging time
Wireless communication
Range
Camera
Aerial acrobatics
Battery
Dimensions
Weight
C0
215g
none
automatic descent
3 m/s
5 m/s
2 m/s
20 min
180 - 210 min
2.4GHz
30-100 m
HD 720P Wi camera
360 ip
3.7V/ 1600mAh Li-Po
305x67x320 mm
140 g
EN
REMOTE CONTROL FUNCTIONS
No. Button Description of functions
Allows you to adjust the ight speed of your drone.Speed control
On/o switch Turns the controller on and o.
Flight direction change/return A short press of the button changes the direction of ight.
Holding the button down for 3 seconds activates the return function.
Right stick Forward/backward/sideways ight.
Press the button briey to take a picture.
Holding the button down for 3 seconds enables video recording.
Press the button again briey to stop recording.
If the drone moves to the right on its own, press the button to trim.Right ight trim
Backward movement trimmer If the drone moves forwards on its own, press the button to trim.
Emergency landing A long press on this button causes an immediate stop.
Climbing/descending/rotating around its own axis.Left stick
Flip 360° Allows you to rotate the drone 360 degrees - 3D rotation function.
If the drone moves to the left on its own, press the button to trim.
Left ight trim
1.
2.
Camera3.
4.
5.
If the drone moves backwards on its own, press the button to trim.Forward movement trimmer6.
7.
12.
8.
9.
10.
Press the button to start the motors.
Press the button again to raise the drone to the specied height.
In normal ight mode, tap this key again to slowly land the drone on the ground.
Take-o/landing button11.
13.
14. LED If the LED ashes, it means the drone is not connected to the controller.
Move the left stick up and down to correctly complete the pairing process.
If the LED lights steady, it means that the controller is in ight control mode.
14
11
5
6
4
2
13
9
7
1
3
8
10
12
EN
CONTROLLER BATTERY INSTALLATION
1.Loosen the screw and remove the battery cover.
2.Insert 3xAA batteries into the controller according to the indicated polarity.
3.Place the battery cover in place and secure it with the screw.
Apple Store search KY FPV
(Please scan this QR code to install
this software).
Google play search KY FPV
(Please scan this QR code to install
this software).
APP INSTALLATION:
After installing the software from the App Store or Google Play, in the phone options, Wi-Fi network settings, search for the
UGO Mistral 3 WIFI as an available network and connect your phone to it. After connecting to the network correctly, run the
app and select PLAY.
FLIGHT PREPARATION
1.Install the batteries in the drone and controller. Then turn on the power button on the drone and the LED on the drone will
light up. Place the drone on a level surface.
2.Turn on the controller, move the left stick up and down. The lights on the fuselage will illuminate and the controller will be
successfully connected.
DRONE CONTROL DURING FLIGHT
1.The left controller stick is responsible for the drone's climbing and descent. When you move the stick up, the drone will
begin to climb. When you move it down, the drone will begin to descend.
2.Moving the left control stick to the left will cause the drone to rotate counter-clockwise around its axis. Moving the left
control stick to the right will cause the drone to rotate clockwise around its axis.
3.Moving the right stick to the left will make the drone y to the left. Moving the right stick to the right will make the drone
y to the right
DRONE BATTERY INSTALLATION AND CHARGING
1.Open the battery cover.
2.Connect the batteries to the charging cable provided. Connect the cable to a USB port (PC/Laptop or network adapter).
3.During charging, the LED glows continuously. After charging, the LED will go out. Estimated charging time is 180-210 min.
4.Disconnect the battery from the charger by releasing the safety catch (photo 2 from the battery side) and then re-install
the battery in the drone (photo 3).
EN
SWITCHING DRONE SPEED
By default, the drone is set to low speed mode. When you press the speed switching
button and hear a double beep, the drone has medium speed mode enabled.
Pressing the button again will switch the speed mode to the fastest one.
The change will be communicated with a triple beep.
CHANGE OF FLIGHT CONTROL DIRECTION
Pressing and holding the home button for 3 seconds will activate the drone's return mode.
To exit the drone's auto-return mode, press and hold the home button again for 3 seconds or start steering with the right stick.
PROPELLER REPLACEMENT
When a propeller is damaged, remember that propellers marked with the letter A should always be replaced with
the appropriate propellers also marked with the letter A and propellers marked with the letter B should always
be replaced with those marked with the letter B.
PRINCIPLES OF DRONE CONTROL
The operator is obliged to:
• Make sure he has adequate insurance.
• Check that the area in which the ight is to be conducted is not covered by a no-y zone or other restriction.
• Keep the drone in sight at all times.
• Maintain a safe distance between the drone and people, animals and other aircraft.
• Immediately report to your national civil aviation authority if your drone has been involved in an accident involving
serious or fatal injuries to persons or involving manned aircraft.
• Operate the drone according to the manufacturer's instructions.
• Do not y over a gathering of people.
• Do not y higher than 120 m from the nearest point of the ground surface.
• Do not y near aircraft or in the vicinity of airports, airstrips or where rescue operations are in progress.
• Do not violate the privacy of others.
• Do not use drones to transport hazardous materials or drop materials.
• Do not modify the drone. Do not install software other than that recommended by the manufacturer.
PACKAGE CONTENT
• Mistral 3.0 drone
• Controller
• USB cable
• Operating instructions
EN