Znaleziono w kategoriach:
Miksery audio (18)
Wróć
MIX 4 / MIX 4 EQ
User manual
Instrukcja obsługi
ENGLISH
1. Use this balanced XLR jack to connect a microphone to the machine
(applies to channels 1 through 5) The phantom power required for conden-
ser mics can be activated with switch.
2.PAD
If the [PAD] switch is turned on, set the [LEVEL] 10 knob to “0” (minimum),
and then turn off the switch.
3.HPF
Opening the switch enables a high-pass filter that can attenuate the fre-
quency below 80Hz. When speaking to the microphone, you can open the
switch to minimize the unwanted vibration and disruptive operation of the
microphone.
4.The GAIN MIC control determines the channels input gain, both for a mi-
crophone connected via the XLR jack and for other signal sources con-
nected to the 1/4 jack.
5. Use the PAN control to adjust the signal s positon on the stereo ba-
sis.
6. The CHANNEL fader adjusts the volume of the corresponding channel
7. Your machine comes with a 3-band equalizer. the HI control governs
the high frequency range, the MID control can be used to boost/cut the
midrange frequencies, and the LOW control allows you to raise or lower
the gain of the bass range.
8. Use the AUX control to determine the channel volume sent to the
AUX mix bus. When set fully to the left, the channel volume in the AUX mix
is zero.
9. The EFF control adjusts the effects volume for the corresponding
channel.
10.PEAK LED
Lights when the volume of input and/or post-equalizer sound is too high. If
it is lit, turn the [GAIN] 4 knob to the left to lower the volume.
1. Use the TAPE OUT jacks to connect, for example, a tape deck for recording applications.
2. The TAPE IN jacks (on stereo RCA) allow for the connection of play-back devices such as CD,
MIXER, players, etc.
3. These are the two balanced LINE inputs on 1/4 jacks for the left and right sides of the stereo
channels, which can be used in parallel to the microphone inputs.
4. These are the balanced 1/4' jack MAIN OUTPUTS of your machine that can be used to connect,
e.g. a power amplifier.
5. The AUX SEND connector provides the monitor signal of your machine, for example, to control a
monitor amplifier or active monitor speaker.
6. Connect the EFF SEND connector to the input of an external effects device.
7. Use the PHONES jack to connect a commercially available pair of headphones.
8. USB INPUT (Use this input for connect your devices).
9. DISPLAY
10. Press this button to loop the song.
11. Using button, press one song at a time to lower the volume for more than a few seconds.
12. Using button, press one song at a time to raise the volume in more than a few seconds.
13. Use buttons to control player playback or pause.
Note: the signal of MP3 player is controlled by stereo channel 3 and 4.
1. PHANTOM +48V (phantom power supply). Use this switch to
turn on or off a phantom power supply. When this switch is
turned on, the mixer will provide the input socket to 1 and 2 XLR
microphone channel.
2.The LEVEL DISPLAY reads the output level of your machine.
Make sure that the two Clip LEDs won't light up.
3. Power switch
4. This is used for adjusting the time interval of echo repeat. The
middle position (5) may be most effective
5. This is used for adjusting frequency of echo repeat. Since too
much echo repeat may cause a howl.
Please adjust frequency properly.
6. MP3 volume pusher – by adjusting the knob, you can adjust the
MP3 output volume
7.The PHONES control governs the headphones volume.
8. The AUX SEND control adjusts the volume level of the AUX sig-
nal provided at connector.
9. The EFF SEND control allows you to adjust the level that is
sent to an MIXER external effects device via connector. Thus, you
can drive all types of effects devices without any risk of distortion.
WARNING! THE DEVICE MUST NOT BE DISPOSED OF WITH HOUSEHOLD WASTE.
This symbol indicates that this product must not be disposed of with household waste, according to the EU and your
national law. In order to prevent potential damage to the environment or health, the used product must be recycled. In
accordance with current legislation, unusable electrical and electronic devices must be collected separately at the des-
ignated facilities for recycling, acting on the basis of applicable environmental standards.
Information about used electrical and electronic equipment
The main goal of European and national law regulations is to reduce the amount of waste produced from used electrical and
electronic equipment, to ensure an appropriate level of collection, recovery and recycling of used equipment, and to increase
public awareness of its harmfulness to the environment, at each stage of use of electrical and electronic equipment. Therefore,
it should be pointed out that households play a key role in contributing to reuse and recovery, including recycling of used equip-
ment. The user of electrical and electronic equipment – intended for households – is obliged to return it to authorized collector
after its use. However, it should be remembered that products classified as electrical or electronic equipment should be disposed
of at authorized collection points.
POLSKI
1. Użyj tego zbalansowanego wejścia XLR jack aby podłączyć mikrofon
do miksera (kanały 1-5), jeśli używasz mikrofonu pojemnościowego nie-
zbędne będzie aktywowanie zasilania Phantom.
2. PAD
Umożliwia zastosowanie wejść jako liniowych złączy MIC. PAD wyrównuje
najwyższe sygnały wejściowe z instrumentów.
3. HPF
Wciśnięcie tego przełącznika powoduje uruchomienie filtra górnoprzepu-
stowego, który wycina częstotliwości poniżej 80Hz.
4. Potencjometr GAIN reguluje wejściowy poziom sygnału na dany ka-
nał, dotyczy to zarówno mikrofonów, jak i innych urządzeń wejściowych.
5. Użyj pokrętła PAN aby ustawić bilans dźwięku w przestrzeni stereo.
6. Suwak CHANNEL reguluje głośność odpowiadającego mu kanału.
7. Mikser został wyposażony w trzypunktową korekcję barwy. HIGH –
do regulacji poziomu wysokich tonów, MID do średnich, a LOW do niskich
częstotliwości
8. Użyj tego potencjometru aby wyregulować poziom sygnału wycho-
dzącego do szyny AUX mix. Gdy ustawisz go całkowicie w lewą stronę po-
ziom będzie zerowy.
9. Potencjometr EFF reguluje poziom efektu dodawanego do odpowia-
dającego kanału.
10. PEAK LED
Wskaźnik zaświeci się gdy poziom głośności wejściowej, lub po korekcji jest
zbyt wysoki. Jeśli świeci się dioda PEAK użyj potencjometru [GAIN] aby
zmniejszyć poziom sygnału wejściowego.