TT6
EN - Instructions and warnings for
installation and use
IT - Istruzioni ed avvertenze per
l’installazione e l’uso
FR - Instructions et avertissements
pour l’installation et l’utilisation
ES - Instrucciones y advertencias
para la instalación y el uso
DE - Installierungs-und Gebrauchsan-
leitungen und Hinweise
PL - Instrukcje i ostrzeżenia do
instalacji i użytkowania
NL - Aanwijzingen en aanbevelingen
voor installatie en gebruik
Control unit for tubular motors
RS232 interface
22
English - 1
EN
Original instructions
ENGLISH
1 –WARNINGS
•Caution! It is important to observe these instruc-
tions to guarantee the safety of persons.
• Caution! Important safety instructions: store these
instructions in a safe place.
• Caution! All product installation, connection, pro-
gramming and maintenance operations must be
performed exclusively by a qualified and skilled
technician!
• Do not effect modifications to any part of the product
other than those specified in this manual. Unautho-
rised operations can lead to hazards and cause mal-
functions. The manufacturer declines all liability for dam-
ages caused by makeshift modifications to the product.
• Important! - Do not use substances containing alcohol,
benzene, diluents or other flammable substances. Use of
such substances could damage the product.
• Store this manual with care in a safe place to facilitate any
future product maintenance and programming opera-
tions.
• The product packaging material must be disposed of in
full observance of current local regulations governing
waste disposal.
• Use a soft and slightly damp (not wet!) cloth for cleaning
the product’s surfaces.
2 –PRODUCT DESCRIPTION AND INTENDED
USE
The TT6 control unit is designed for use in automation sys-
tems applied to awnings, shutters, skylights, vertical cur-
tains, blinds and for controlling video projection screens.
Any other use is to be considered improper and is
strictly prohibited! The manufacturer declines all liabil-
ity for damage resulting from improper use of the
product and other than as specified in this manual.
The product comprises the following:
- Output for controlling a wire technology motors (for
example, One-Max, To-max or NeoM); the output can be
activated directly through the two buttons: Pup () and
Pdown ();
- TTBUS interface for controlling Nice motors with bus sys-
tem.
- RS232 interface for connection to PC.
- Activation input (Trigger) for activating or deactivating a
sequence of motors (near the up or down trigger).
The radio interface expands the product’s remote control
range through the Nice radio technology.
3 –INSTALLATION
01. Remove the top cover of the control unit (Fig. 1).
02. In the zones marked accordingly, drill the holes for
routing the cables and for fixing the control unit to the
wall. Caution! – Take suitable precautions to
guarantee the IP protection rating required for
the type of installation. In particular, apply cable
clamps (not supplied) to protect the power
2- English
EN
cables and control cables against possible trac-
tion or torsion.
03. Fix the control unit housing to the wall (Fig. 2).
Caution! – The receiver must be positioned so that
the cables enter the housing exclusively from the
bottom.
1
2
4 –ELECTRICAL CONNECTIONS
Warnings
• When connecting the aerial provided, leave the wire at the
supplied length and lay it straight so as to avoid excessive
bending.
• If the control unit is not in an optimal position and the
radio signal is weak, improve reception by replacing the
aerial supplied with an external version (model ABF or
ABFKIT). The new aerial must be positioned as high as
possible and above any metal or reinforced concrete
structures present in the area.
4.1 –Inputs (Fig. 3 and Table 1)
•LElectrical phase
•N Neutral
•TTBUS: (TTBUS, GND)
•RS232 with dedicated protocol
•5-24 VDC trigger with programmable On and Off events
– 30+30 programmable events
– Event: address, command
•Two inputs for open-close commands for 85-265 VAC
50/60 Hz mechanical motor
– Open-STOP, Close-STOP operation
– “ON-PRESS” activation
4.2 –Outputs
• Power relay output for controlling a mechanical/electronic
motor with programmable manoeuvres (up and down), acti-
vated through two button inputs Pup () and Pdown () of
the 12 V Trigger or via Transmitter.
English - 3
EN
TABLE 1
Wiring diagram
1Electrical phase
2Neutral
3Ground
4Up button linked to the connectable mechanical
motor
5Down button linked to the connectable mechanical
motor
6Mechanical motor ground
7Mechanical motor down phase
8Mechanical motor common contact
9Mechanical motor up phase
10 TX signal of the RS232 interface
11 RX signal of the RS232 interface
12 Common contact (GND) of the RS 232 serial signal
13 Signal of the motor with TTBUS (White wire)
14 Common contact of the motor with TTBUS (White/
Black wire)
15 External activation trigger signal (positive pole input)
16 External activation trigger common contact (nega-
tive pole input)
ANT Aerial input
– The activation timer can be adjusted to between 1 sec.
and 240 sec. through the serial port with an internal com-
mand.
– The default address of the motor connected to the control
unit is 1.
Refer to Table 2 to check the LEDs present.
16
P
POWER
SUPPLY
100 - 240 V
50 - 60 Hz
TTBUS
TRIGGER 12 V
AERIAL
P
SG
DL7 RL1 PP
DL8 RL2
DL5 P DL4 TRG
DL6 P
DL3 DL2 DL1
23
RS232
5
SG
3