Instrukcja obsługi Szlifierka kątowa RYOBI RAG18BL-0

Znaleziono w kategoriach:

Szlifierki kątowe (1)

Wróć

RAG18X

RAG18BL

Important! It is essential that you read the instructions in this manual before assembling, maintaining and

operating the product.

Attention! Il est essentiel que vous lisiez les instructions contenues dans ce manuel avant d’assembler,

d’entretenir et d’utiliser le produit.

Achtung! Es ist wichtig, dass Sie vor Zusammenbau, Wartung und Benutzung des Produktes die Anweisungen

in dieser Anleitung lesen.

¡Atención! Resulta fundamental que lea este manual de instrucciones antes de realizar el montaje, el

mantenimiento y de utilizar este producto

Attenzione! E’ importante leggere le istruzioni contenute nel presente manuale prima di montare il prodotto,

svolgere le operazioni di manutenzione sullo stesso e metterlo in funzione.

Let op! Het is van essentieel belang dat u de instructies in deze gebruiksaanwijzing leest voor u het product

monteert, onderhoudt en gebruikt.

Atenção! É fundamental que leia as instruções deste manual antes da montagem, manutenção e operação

do aparelho.

OBS! Det er vigtigt, at man læser instrukserne i denne brugsanvisning, inden man samler, vedligeholder

og betjener produktet.

Observera! Det är viktigt att du läser instruktionerna i manualen före montering, användning och underhåll av

produkten.

Huomio! On tärkeää, että luet tämän käsikirjan ohjeet ennen tuotteen kokoamista, huoltoa ja käyttöä.

Advarsel! Det er viktig at du leser instruksjonene i denne manualen før sammensetning, vedlikehold og bruk

av produktet

Внимание! Необходимо прочитать инструкции в данном руководстве перед сборкой, обслуживанием и

эксплуатацией этого изделия.

Uwaga! Koniecznie należy przeczytać instrukcje zawarte w tym podręczniku przed montażem, obsługą oraz

konserwacją produktu.

Důležité

upozornění! Neinstalujte, neprovádějte údržbu ani nepoužívejte tento výrobek dříve, než si přečtete pokyny

uvedené v tomto návodu.

Figyelem! Fontos, hogy a termék összeszerelése, karbantartása és használata előtt elolvassa a kézikönyvben

található utasításokat.

Atenţie! Este esențial să citiți instrucțiunile din acest manual înainte de asamblare, efectuarea întreținerii și

operarea produsului.

Uzmanību! Ir svarīgi izlasīt šīs rokasgrāmatas instrukcijas pirms uzstādīšanas, apkopes un preces darbināšanas.

Dėmesio! Prieš surenkant, prižiūrint ir naudojant gaminį, būtina perskaityti šiame vadove pateiktus nurodymus.

Tähtis! Enne masina kokkupanekut, hooldamist ja kasutama hakkamist tuleb käesolevas juhendis esitatud

juhised kindlasti läbi lugeda.

Upozorenje!

Vrlo je važno da ste prije sklapanja, održavanja i rada s ovim proizvodom pročitali upute u ovom priručniku.

Pomembno!

Pomembno je da pred montažo vzdrževanjem in uporabo tega izdelka preberete navodila v tem priročniku.

Upzornenie! Je dôležité, aby ste si pred montážou, údržbou a obsluhou produktu prečítali pokyny v tomto návode.

Важно! Изключително важно е да прочетете инструкциите в настоящото ръководство, преди да

преминете към сглобяване, поддръжка или работа с продукта.

Важливо! Дуже важливо, щоб ви прочитали інструкції в цьому керівництві перед складанням,

обслуговуванням та експлуатацією цієї машини.

Dikkat! Ürünün montajını, bakımını yapmadan ve ürünü çalıştırmadan önce bu kılavuzda yer alan talimatları

okumanız önemlidir.

Προσοχή! Είναι πολύ σημαντικό να διαβάσετε τις οδηγίες στο παρόν εγχειρίδιο πριν συναρμολογήσετε,

συντηρήσετε ή λειτουργήσετε το προϊόν.

Subject to technical modication | Sous réserve de modications techniques | Technische Änderungen vorbehalten | Bajo

reserva de modicaciones técnicas | Con riserva di eventuali modiche tecniche | Technische wijzigingen voorbehouden

| Com reserva de modicações técnicas | Med forbehold for tekniske ændringer | Med förbehåll för tekniska ändringar |

Tekniset muutokset varataan | Med forbehold om tekniske endringer | могут быть внесены технические изменения |

Z zastrzeżeniem modykacji technicznych | Změny technických údajů vyhrazeny | A műszaki módosítás jogát fenntartjuk

| Sub rezerva modicaţiilor tehnice | Paturam tiesības mainīt tehniskos raksturlielumus | Pasiliekant teisę daryti techninius

pakeitimus | Tehnilised muudatused võimalikud | Podloæno tehniëkim promjenama | Tehnične spremembe dopuščene

| Právo na technické zmeny je vyhradené | Подлежи на технически модификации | Є об’єктом для технічних змін |

Teknik değişiklik hakkı saklıdır | Υπό την επιφύλαξη τεχνικών τροποποιήσεων

Safety, performance, and dependability have been given

top priority in the design of your angle grinder.

INTENDED USE

The angle grinder is intended to be used only by adults who

have read and understood the instructions and warnings in

this manual, and can be considered responsible for their

actions.

The product is designed for grinding and cutting metals

and stone materials. Only appropriate grinding discs as

described in the product speciﬁ cations section of this

manual should be ﬁ tted to the angle grinder.

The product is intended for dry use only. Do not use the

product for wet applications.

The product is designed for handheld use. The product is

not to be mounted onto a workbench.

The product is intended for consumer use only.

Do not use the product for any other purpose. Use of the

product for operations different from intended could result in

a hazardous situation.

WARNING! Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

SAFETY WARNINGS COMMON FOR GRINDING OR

CUTTING-OFF OPERATIONS:

■This power tool is intended to function as a grinder

or cut-off tool. Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury.

■Operations such as sanding, wire brushing,

polishing or hole-cutting are not to be performed

with this power tool. Operations for which the power

tool was not designed may create a hazard and cause

personal injury.

■Do not convert this power tool to operate in a way

which is not specifically designed and specified by

the tool manufacturer. Such a conversion may result

in a loss of control and cause serious personal injury.

■Do not use accessories which are not specifically

designed and specified by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

■The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

■The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

■The dimensions of the accessory mounting must

fit the dimensions of the mounting hardware of the

power tool. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

■Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test

time.

■Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various applications. The dust

mask or respirator must be capable of filtrating particles

generated by the particular application. Prolonged

exposure to high intensity noise may cause hearing loss.

■Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away and

cause injury beyond immediate area of operation.

■Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

■Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

■Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

■Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

■Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

■Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation at the point of binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either

jump toward or away from the operator, depending on the

direction of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

ENGLISH

Original Instructions

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

■Maintain a firm grip with both hands on the power

tool and position your body and arms to allow you to

resist kickback forces. Always use auxiliary handle,

if provided, for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper

precautions are taken.

■Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

■Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point of snagging.

■Use special care when working corners, sharp

edges, etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

■Do not attach a saw chain woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such

blades create frequent kickback and loss of control.

Safety warnings specific for grinding and cutting-off

operations

■Use only wheel types that are specified for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was

not designed cannot be adequately guarded and are

unsafe.

■The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequately protected.

■The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

■Wheels must be used only for specified applications.

For example, do not grind with the side of cut-

off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

■Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-off

wheels may be different from grinding wheel flanges.

■Do not use worn down wheels from larger power

tools. A wheel intended for larger power tool is not

suitable for the higher speed of a smaller tool and may

burst.

■When using dual purpose wheels always use the

correct guard for the application being performed.

Failure to use the correct guard may not provide the

desired level of guarding, which could lead to serious

injury.

Additional safety warnings specific for cutting-off

operations

■Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or binding of the

wheel in the cut and the possibility of kickback or wheel

breakage.

■Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

■When the wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

it motionless until the wheel comes to a complete

stop. Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion otherwise

kickback may occur. Investigate and take corrective

action to eliminate the cause of wheel binding.

■Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

■Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

■Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

■Do not attempt to do curved cutting. Overstressing

the wheel increases the loading and susceptibility

to twisting or binding of the wheel in the cut and the

possibility of kickback or wheel breakage, which can

lead to serious injury.

ADDITIONAL SAFETY WARNINGS

■Clamp workpiece with a clamping device. Unclamped

workpieces can cause severe injury and damage.

■Do not switch on the product again after it has stalled.

Switching it on again, can cause a kickback with high

reaction force. Determine why the product has stalled

and rectify it, paying heed to the safety instructions. If

necessary, remove the insertion tool.

■Injuries may be caused, or aggravated, by prolonged

use of a tool. When using any tool for prolonged periods,

ensure you take regular breaks.

■Ambient temperature range for tool during operation is

between 0°C and 40°C.

■Ambient temperature range for tool storage is between

0°C and 40°C.

■The recommended ambient temperature range for the

charging system during charging is between 10°C and

38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

To reduce the risk of ﬁ re, personal injury, and product

damage due to a short circuit, never immerse your tool,

battery pack, or charger in ﬂ uid or allow ﬂ uid to ﬂ ow inside

4Original Instructions

them. Corrosive or conductive ﬂ uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing

products, etc., can cause a short circuit.

■Ambient temperature range for battery during use is

between 0°C and 40°C.

■Ambient temperature range for battery storage is

between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps or

tape. Do not transport batteries that are cracked or leaking.

Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 109.

1. Battery port

2. Handle, insulated gripping surface

3. Spindle lock button

4. Side handle

5. Guard lever lock

6. Toolless grinding guard

7. Paddle switch

8. Lock-out switch

9. Clamp nut

10. Operator’s manual

11. Grinding wheel

12. Cutting disc

13. Backing flange

14. Spindle shaft

15. Toolless cutting guard attachment

16. Battery pack

17. Charger

MAINTENANCE

■The product should never be connected to a power

supply when assembling parts, making adjustments,

cleaning, performing maintenance, or when the product

is not in use. Disconnecting the product from the power

supply will prevent accidental starting that could cause

serious injury.

■When servicing, use only original manufacturer’s

replacement parts, accessories, and attachments. Use

of any other parts may create a hazard or cause product

damage.

■Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken, or

destroy plastic which may result in serious personal

injury.

■Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to various types of commercial

solvents and may be damaged by their use. Use clean

cloths to remove dirt, carbon dust, etc.

■For greater safety and reliability, all repairs should be

performed by an authorised service centre.

SYMBOLS

Safety alert

Direct current

Please read the instructions carefully before

starting the product.

Wear ear protection.

Wear eye protection.

Wear dust mask.

Wear safety hand gloves.

Wear non-skid safety shoes.

Always operate with two hands.

Do not use the guard for cut-off operations.

Do not use chipped, cracked, or defective

grinding wheel

Do not use for cutting.

Use a guard.

Metal

Not for wet grinding. Using water or other

liquid coolants may result in electrocution

or shock.

Do not use for face grinding.

ENGLISH

Original Instructions

Znaleziono w kategoriach:

Instrukcja obsługi Szlifierka kątowa RYOBI RAG18BL-0

NOWOŚCI

GAMING

NA CZASIE

PORADNIK MEDIA EXPERT

POMYSŁ NA PREZENT

Najnowsze poradniki

Ranking tabletów dla seniora [TOP10]

Ranking słuchawek sportowych [TOP10]

Ranking telefonów do 5000 zł [TOP10]

Nadlatuje dron Antigravity A1. W ten sposób Insta360 chce zmienić zasady gry

Ranking konsol przenośnych [TOP10]

Ranking książek dla 2–latka [TOP10]

Jak fotografować las?

Jak złowić sandacza i inne ryby?

Ranking lodówek do 1000 zł [TOP10]

Ranking suszarek do włosów [TOP10]

Ranking multicookerów [TOP10]

Ranking zmywarek do zabudowy 60 cm [TOP10]

Ranking trenażerów rowerowych [TOP10]

Ranking suchych karm dla psa [TOP10]

Ranking pił stołowych [TOP10]

Sprzedaż dla firm i instytucji

Ubezpieczenia "Gwarancja PLUS"

Zakupy na raty przez internet

Karty podarunkowe Media Expert