Znaleziono w kategoriach:
Czujnik ciepła FIREANGEL HT-630-EUT

Czujnik ciepła FIREANGEL HT-630-EUT

Wróć
Heat Alarm HT-630
Heat Alarm with Wireless Interlink WHT-630
6 7
After completing the ‘learn-in’ procedure,
test the alarms as described in ‘ALARM
TEST’. If any interlinked alarm fails to
respond to the ‘ALARM TEST’, remove
it from its base plate and repeat the
‘learning-in’ process.
Unlearning a Wi-Safe 2 Alarm
To remove an alarm from a network, push
and release, then push and hold the learn
button. When the red LED goes out, release
the button. Once the LED has flashed 5
times you have successfully ‘Unlearned’
the alarm.
When removing an alarm from any Wi-Safe
2 network it is generally good practice to
“unlearn” every alarm (in the same way as
mentioned above) and rebuild the network
once again by following the “learn-in”
process on page 4.
Please note it is important not to rush
the Wi-Safe 2 system and is also good
practice to allow several minutes after
unlearning the system before rebuilding
the network once again.
ALARM TEST
1. Briefly press the test button in the
centre and release.
2. The unit will give an audible alarm
consisting of 2 cycles of 3 loud beeps,
then stop automatically.
3. The red LED on the alarm will flash
rapidly during the audible signal.
As with all electronic alarm products you
should test your heat alarm every week, as
well as any other interlinked alarms.
WARNING: The electronic test button
provides a full test of the alarms
functionality. DO NOT try to test the alarm
with a naked flame, as this might present a
fire hazard in itself.
MAINTENANCE
Vacuum every three months to help keep
the unit working efficiently. Vacuum the
exterior. Prevent vacuum from touching the
unit.
TROUBLESHOOTING
If your heat alarm chirps intermittently:
• Check the location of your alarm.
• If the alarm chirps every 45 seconds
and the amber LED flashes at the same
time, this indicates that the power pack
is low. Replace the unit within 30 days.
• WHT-630 only: If the alarm chirps every
4 hours, another alarm in the network
has a low power pack and needs
replacing.
If the amber LED is flashing and the alarm
is chirping:
• If the amber LED flashes at a different
time to the chirp, this means there’s
a fault with your alarm and it needs
replacing.
If your heat alarm does not sound during
testing:
• Push the centre test button firmly.
• If the unit has been silenced and is in
low sensitivity mode, it may not sound.
Wait 15 minutes.
• Make sure the alarm is securely located
into the base plate.
If the alarm fails to operate correctly
contact Technical Support on: 0800 141
2561.
DISPOSAL
Waste electrical products should not be disposed
of with your other household waste. The alarm is
ideally suited for disposal within the waste electronic
and electrical equipment (WEEE) recycling scheme.
Please recycle where facilities exist. Check with
your local authority, retailer or contact our technical
support team for recycling/disposal advice as
regional variations apply. Once the alarm is
removed from the base plate the internal power pack
(battery) will be deactivated. The unit is now ready for
disposal.
WARNING: Do not attempt to open. Do not burn or
dispose of in fire.
WARRANTY
Sprue Safety Products Ltd warrants to the original
purchaser that its enclosed heat alarm be free from
defects in materials and workmanship under normal
residential use and service for a period of 5 years
for the WHT-630 and 10 years for the HT-630 from
the date of purchase. Provided product is sent back
to Sprue Safety Products with proof and date of
purchase, Sprue Safety Products Ltd hereby warrants
that during the 5 year period (10 year on the HT-630)
commencing from the date of purchase Sprue Safety
Products Ltd, at its discretion, agrees to replace the
unit free of charge.
The warranty on any replacement HT-630/WHT-630
alarm, will last for the remainder of the period of the
original warranty in respect of the alarm originally
purchased – that is from the date of original purchase
and not from the date of receipt of the replacement
product. Sprue Safety Products Ltd reserves the right
to offer an alternative product similar to that being
replaced if the original model is no longer available
or in stock. This warranty applies to the original retail
purchaser from the date of original retail purchase
and is not transferable. Proof of purchase is required.
User Manual
Please retain this user manual for future reference
This warranty does not cover damage resulting
from accident, misuse, disassembly, abuse or lack
of reasonable care of the product, or applications
not in accordance with the user manual. It does not
cover events and conditions outside of Sprue Safety
Products Ltd’s control, such as Acts of God (fire,
severe weather etc.). It does not apply to retail stores,
service centres or any distributors or agents. Sprue
Safety Products Ltd will not recognise any changes to
this warranty by third parties.
Sprue Safety Products Ltd shall not be liable for any
incidental or consequential damages caused by the
breach of any expressed or implied warranty. Except
to the extent prohibited by applicable law, any implied
warranty of merchantability or fitness for a particular
purpose is limited in duration for 5 years on the WHT-
630 and 10 years on the HT-630. This warranty does
not affect your statutory rights. Except for death or
personal injury, Sprue Safety Products Ltd shall
not be liable for any loss of use, damage, cost or
expense relating to this product or for any indirect or
consequential loss, damages or costs incurred by you
or any other user of this product. Please see the back
cover of this guide for contact details.
8
2 3 4 5
Features . . . . . . . . . . . . . . 3
Where to locate . . . . . . . . . . 3
Installation. . . . . . . . . . . . .4
Wireless interlink
(WHT-630 only) . . . . . . . . . . 4
Note: This user guide is also available in large text and other formats.
Please call 0800 141 2561 for further information.
CONTENTS
Alarm test . . . . . . . . . . . . . 6
Maintenance. . . . . . . . . . . .6
Troubleshooting. . . . . . . . . .6
Disposal . . . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . .7
IMPORTANT INFORMATION!
FEATURES
• Fixed point heat alarm, Class A1 with
alarm point temperature 56°C - 64°C.
• Thermistor heat sensing element for
accuracy, reliability and stability.
• Thermistek technology activates the
alarm sooner if it predicts a significant
rate of rise in temperature.
• 10 year, sealed for life battery.
• Operating red LED flashes once,
approximately every 45 seconds.
• Fault indication - amber LED flashes to
indicate a low battery condition or alarm
fault. See Troubleshooting.
• Central Test/Silence ( ) button. Tests
circuitry, battery and sounder.
• Loud 85 decibel piezo sounder.
• Automatically resets when alarm
condition has passed.
• Easy installation. Fixings supplied.
• Silencer. In the event of a known false
alarm your alarm can be temporarily
silenced by briefly pressing the central
test button. Your alarm will automatically
return to full sensitivity within 10
minutes.
• WHT-630 includes Wi-Safe 2 technology,
allowing you to wirelessly interlink up
to 50 heat alarms, smoke alarms and
accessories , which contain Wi-Safe 2
technology, and can be either battery or
mains powered.
WHERE TO LOCATE
For the best protection heat alarms should
always be installed as part of a complete
fire protection system that also includes
smoke alarms. Heat alarms are best suited
to areas where dust, fumes and moisture
can cause nuisance alarms in smoke
alarms, such as:
• Boiler rooms
• Kitchens
• Laundry rooms
• Lofts
• Garages
Heat alarms should not be installed in
escape routes instead of smoke alarms.
They should only be used in the above
applications and where possible be
interlinked to smoke alarms. (Smoke
alarms should be installed in circulation
areas forming part of the escape routes
and in every room in the house.)
When heat alarms are installed in a room,
they should be placed on the ceiling, ideally
in the centre of the room. They should be
at a distance no greater than 5.3m from the
farthest wall, no greater than 5.3m from a
door to any room in which a fire might
start and no greater than 5.3m from the
next heat alarm.
NOTE: HEAT ALARMS SHOULD NOT BE
WALL MOUNTED.
Install sufficient alarms to compensate for
closed doors and obstacles, which may
interfere with the path of heat to an alarm
and may prevent occupants from hearing
an alarm.
Smoke alarms for limited protection
Dwelling with
one sleeping area
Dwelling with more
than one sleeping area
Additional smoke alarms for better coverage
Heat alarms
Dining
Room
TV
Room
Living
Room
Living
Room
Kitchen Kitchen
Bedroom Dining
Room
Bedroom
Bedroom
Two storey
dwelling
Living
Room
Hall
Hall Kitchen Garage
Bedroom Bedroom
Bedroom
Bedroom
Bedroom
Loft
IMPORTANT: These heat alarms are
intended primarily for use in single
occupancy private dwellings. For use
in other applications the manufacturers
advice should be sought.
INSTALLATION
IMPORTANT: Please read ‘WHERE TO
LOCATE’ before installing the alarm.
Fit the base plate to the ceiling using the
screws provided (knock-out the tabs as
required).
To fit the alarm to the base plate included
in this pack, position the alarm on the
plate, then turn clockwise until the alarm
is locked into position. Make sure that the
alarm is twisted fully. The power pack will
now activate. The red LED on the front
of the alarm should flash once every 45
seconds to show that it is active.
WIRELESS INTERLINK
(WHT-630 only)
The WHT-630 heat alarm contains an
inbuilt RF module, which enables you
to wirelessly interlink up to 50 Wi-Safe 2
products to create a network. Therefore the
WHT-630 alarms need to be ‘learned-in’ or
interlinked in order to communicate with
each other , or other alarms with Wi-Safe
2 technology.
Once a network has been established, if
one alarm activates, all other interlinked
alarms will also sound. Please note that
WHT-630s can only be interlinked with
other WHT-630s and products within the
Wi-Safe 2 range.
The process below describes ‘learning-in’
two alarms into a network, ‘Alarm 1’ and
‘Alarm 2’:
1. Install ‘Alarm 1’ as described previously.
2. Install the base plate for ‘Alarm 2’ in
one of the recommended locations. Do
not fit the second alarm onto its base
plate yet.
3. On ‘Alarm 2’, using a ballpoint pen or a
paperclip opened out, briefly push and
release the learn button , located in a
circular hole in the back of the alarm.
Circular hole
Learn-in button
4. The red LED next to the learn button
will flash briefly then light up for 5
seconds to show it’s ready to receive
the ‘learn-in’ signal. During these
5 seconds you will need to briefly
press the test button on ‘Alarm 1’ to
wirelessly interlink the two alarms.
5. ‘Alarm 1’ will give an audible sound
consisting of 2 cycles of 3 loud beeps.
The red LED on the wireless module of
‘Alarm 2’ will flash to indicate that it has
been ‘learned-in’ successfully.
6. PLEASE NOTE: If the test button is
not pressed quickly enough (before
the red LED on ‘Alarm 2’ has gone
out), the ‘learn-in’ process will fail.
If this happens, repeat the process
again, as described above.
7. Fit ‘Alarm 2’ onto its base plate to
complete the installation.
Additional alarms should be ‘learned-
in’ in the same way. When ‘learning-in’
additional alarms, any alarm already in
the network can be used as ‘Alarm 1’.
This means that you can ‘learn-in’ the
additional alarm, into any alarm already
in the network. It will then become part of
the network. You do not have to ‘learn-in’
to each alarm in the network.
BS5446-2:2003
KM607094
HT-630 / WHT-630
GN2673R2
IMPORTANT: This user guide contains important information regarding the operation of
your FireAngel heat alarm. Ensure you read this user guide fully before installing and
operating this alarm. If you are installing this heat alarm for use by others, you must leave
this guide (or a copy of it) with the end user.
IF THERE IS ANY QUESTION AS TO THE CAUSE OF THE ALARM, ALWAYS ASSUME THAT
THIS IS AN ACTUAL FIRE AND FOLLOW YOUR FIRE EMERGENCY PLANS.
Sprue Safety Products Ltd. Vanguard Centre, Coventry CV4 7EZ UK www.sprue.com
A Sprue Brand
WHT-630 is independently
certified to:
EN 300220-2 v2.4.1
EN 301489-3 v1.6.1
EN 301489-1 v1.9.2
Hereby, Sprue Safety Products Ltd, declares that
this WHT-630 is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC. The declaration of
conformity may be consulted at
http://spru.es/EC-WHT-630

Najnowsze poradniki

Zobacz więcej
Obroża Fi

Obroża Fi Series 3+ powie ci wszystko o twoim psie. To wyjątkowo analityczne urządzenie

miauczenie kota

Miauczenie kota – jak je poprawnie interpretować?

ranking małych pralek

Ranking małych pralek - najlepsze małe pralki

telewizor do 2000

Ranking telewizorów do 2000 zł - najlepsze telewizory do 2000 zł

jak piec pizze w piekarniku

Jak piec pizzę w piekarniku?

najlepsze biurko komputerowe ranking

Najlepsze biurka – ranking biurek komputerowych

lego technic do 500 zł

Najlepsze LEGO Technic do 500 zł - ranking LEGO Technic do 500 zł

najlepsza glebogryzarka elektryczna

Najlepsze glebogryzarki elektryczne - ranking glebogryzarek elektrycznych

książki naukowe

Najlepsze książki popularnonaukowe - ranking książek popularnonaukowych

żelazka ranking

Ranking żelazek - najlepsze żelazka

kardiowatch ranking

Ranking kardiowatchy - najlepsze kardiowatche

najlepsza kawa ziarnista

Najlepsza kawa ziarnista - ranking kaw ziarnistych

depilator laserowy ranking

Ranking depilatorów laserowych - najlepsze depilatory laserowe

jakie zabawki dla noworodka

Jakie zabawki dla noworodka wybrać?

historia roweru

Historia roweru – kiedy wynaleziono rower?

Sprawdź więcej poradników

Pobierz aplikację mobilną Media Expert

Pobierz z Google Play
Pobierz z App Store

Właściciel serwisu: TERG S.A. Ul. Za Dworcem 1D, 77-400 Złotów; Spółka wpisana do Krajowego Rejestru Sądowego w Sądzie Rejonowym w Poznań-Nowe Miasto i Wilda w Poznaniu, IX Wydział Gospodarczy Krajowego Rejestru Sądowego pod nr KRS 0000427063, Kapitał zakładowy: 41 687 500,00 zł; NIP 767-10-04-218, REGON 570217011; numer rejestrowy BDO: 000135672. Sprzedaż dla firm (B2B): dlabiznesu@me.pl INFOLINIA: 756 756 756