Znaleziono w kategoriach:
Lampa błyskowa QUADRALITE Stroboss 60 II do Canon

Lampa błyskowa QUADRALITE Stroboss 60 II do Canon

Wróć
Foreword
Thank You for purchasing this product.
This Stroboss 60 II camera flash applies to camera compatible with E-TTL II autoflash. With this E-TTL
II compatible flash, your shooting will become simpler. You can easily achieve a correct flash exposure
even in complex light-changing environments. This camera flash features:
•Approx. GN60 (ISO 100,@200mm), 81 steps from 1/1 to 1/256.
•Fully support Canon E-TTL II camera flash. Workable as Transmitter or Receiver unit in a
wireless flash group.
•Use dot-matrix LCD panel to make clear and convenient operations.
•With built-in 2.4GHz wireless remote system to support transmitting and receiving.
•Provided multiple functions, include HSS (up to 1/8000s), FEC, FEB, etc.
•Stable consistency and color temperature with good even lighting.
•Support with firmware upgrade.
Warning
•Always keep this product dry. Do not use in rain or in damp conditions.
•Do not disassemble. Should repairs become necessary, this product must be sent to an
authorized maintenance center.
•Keep out of reach of children.
Stop using this product if it breaks open due to extrusion, falling or strong hit. Otherwise,
electric shock may occur if you touch the electonic parts inside it.
•Do not fire the flash directly into the eyes (especially those of babies) within short
distances. Otherwise cisual impairment may occur.
•Do not use the flash unit in the presence of flammable gases, chemicals and other
similar materials. In certain circumstance, these materials may be sensitive to the strong
light emitting from this flash unit and fire or electromagnetic interference may result.
•Do not leave or store the flash unit if the ambient temperature reads over 50°C.
Otherwise the electronic parts may be damaged.
•Turn off the flash unit immediately in the event of malfunction.
Conventions used in this Manual
•This manual is based on the assumption that both the camera and camera flash's power
switches are powered on.
•The automatic light measurement system is marked in this manual with the E-TTL, which
is the correct abbreviation for the Canon brand, for other brands these are i-TTL (Nikon),
TTL(SONY), etc.
•The pictures show an example lamp for the Canon system.
•The following alert symbols are used in this manual:
The Caution symbol indicates a warning to prevent shooting problem.
The Note symbol gives supplemental information.
-2-
CONTENTS
2 Foreword
2 Warning
4 Name of Parts
4 - Body
4 - Control Panel
5 - LCD Panel
5 - LCD Panel in Three Modes
6 What's in the Box of Stroboss 60 II?
6Separately Sold Accessories
6 Loading and Unloading the Battery
6 Attaching to a Camera
7 Power Management
7 Flash Mode – E-TTL Autoflash
7- FEC (Flash Exposure Compensation)
7 - FEB (Flash Exposure Bracketing)
8 - FEL (Flash Exposure Lock)
8 - High-Speed Sync
8 - Second-Curtain Sync
8 M: Manual Flash
9 Multi: Stroboscopic Flash
10 Wireless Flash Shooting: Radio (2.4G) Transmission
11 - Wireless Settings
11 - Transmitter Unit's Flash OFF
12 - Setting the Comunication Channel
12 - Wireless ID Settings
12 - Scan the Spare Channel
13 - ETTL: Fully Automatic Wireless Flash Shooting
14 - M: Wireless Flash Shooting with Manual Flash
14 - Multi: Wireless Flash Shooting with Manual Flash
14 Other Applications
14 Sync Triggering
14 Auto Focus Assist Beam
14 Bounce Flash
15 ZOOM: Setting the Flash Coverage
15 Low Battery Warning
16 C.Fn: Setting Custom Functions
16 Protection Function
17 Technical Data
18 Troubleshooting
18 Firmware Upgrade
18 Compatible Camera Models
18 Maintenance
-3-
Name of Parts
Body
01 Flash Head 07. Battery Cover
02 Built-in Wide Panel 08. Hotshoe
03. Wireless Sensor 09. LCD Panel
04. Focus Assist Beam 10. Hotshoe Fixing Buckle
05. Sync Cord Jack 11. External Charging Port
06. Type-C USB Port
Control Panel
11. <MENU> Flash Menu Button 18. <MODE> Mode Selection Button
12. < > Wireless Selection Button 19. < > Lock Setting
13. Select Dial 20. <+/-> Power Output
14. Set Button 21. Function Button 1
15. ON/OFF Power Switch 22. Function Button 2
16.< > Test Button Flash Ready Indicator 23. Function Button 3
17. <ZOOM> Focus Length Setting 24. Function Button 4
-4-
LCD Panel
(1) E-TTL Autoflash
•The display will only show the settings currently applied.
•The functions displayed above function buttons 1 to 4, such as and
<A/B/C/D>, change according to setting's status.
•The LCD panel will lighten on when buttons and dials are operated.
(2)M: Manual Flash
(3) Multi Flash
(4) Radio Transmission Shooting
Transmitter Unit (TX)
Receiver Unit (RX)
LCD Panel in Three Modes
Attached to the Camera
-5-
2.4G Radio Transmission: As a Transmitter Unit
2.4G Radio Transmission: As a Receiver Unit
What's in the Box of Stroboss 60 II?
1. Flash Unit
2. Mini Stand
3. Protection Case
4. Instruction Manual
Separately Sold Accessiories
This product can be used in combination with the following accessories sold separately, so as to
achieve best photography effects:
Quadralite Navigator XC, Quadralite Navigator, Quadralite S-holder, etc
Loading and Unloading the Battery
1. To unload the battery, hold down the battery and press
compartment and push the battery downwardly to take it out.
2. Put 4 batteries in with the correct polarity after opening the
battery compartment, then close and push it to the top.
Attaching to a Camera
1. Attach the Camera Flash.
Rotate the hotshoe fixing buckle to the left and insert the
camera flash into the camera's hotshoe.
2. Secure the Camera Flash.
Rotate the hotshoe fixing buckle to the right until it locks up.
3. Detach the Camera Flash.
Press the button and rotate the hotshoe fixing buckle to the
left until it is loosened.
-6-
Power Management
Use ON/OFF Power Switch to power the flash unit on or off. Turn off if it will not be used for an
extended period of time. Setting as a transmitter flash, it will turn the power off automatically after a
certain period (approx. 90 seconds) of idle use. Pressing the camera shutter halfway or pressing any
flash button will wake up the flash unit. Setting as a receiver flash, it will enter sleep mode after a
certain period (adjustable , 60 minutes by default) of idle use. Pressing any flash button will wake it up.
Disabling Auto Power Off function is recommended when the flash is used off camera
(C.Fn-STBY)
Receiver Auto Power Off Timer is set to 60 minutes by default. Another option "30
minutes" is available (C.Fn-RX STBY).
FLASH MODE-ETTL Autoflash
This flash has three flash modes: E-TTL, Manual (M), and Multi (Stroboscopic). In E-TTL mode, the
camera and the flash will work together to calculate the correct exposure for the subject and the
background. In this mode, mulstiple TTL functions are available: FEC, FEB, FEL, HSS, second curtain
sync, modeling flash, control with the camera's menu screen.
Press <MODE> Mode Selection Button and three flash modes will display on the LCD panel one by
one with each pressing.
ETTL Mode
Press <MODE> Mode Selection Button to enter E-TTL mode. The LCD panel will display.
•Press the camera release button halfway to focus. The aperture and effective flash range
will be displayed in the viewfinder.
•When the shutter button is fully pressed, the flash will fire a pre-flash that the camera will
use to calculate exposure and flash output the instant before the photo is taken.
FEC: Flash Exposure Compensation
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops. It is useful in situations where
minor adjusting of the TTL system is needed based on the environment.
1. Press the (+/-> button. The icon and flash exposure
compensation amount will be highligted on the LCD panel.
2. Set the flash exposure compensation amount.
Turn the Select Dial to set the amount.
"0.3" means 1/3 step, "0.7" means 2/3 step.
To cancel the flash exposure compensation, set the
amount to "+0".
3. Press Set Button again to confirm the setting.
FEB: Flash Exposure Bracketing
You can take three flash shots while automatically changing the flash output for each shot from -3 to
+3 in 1/3rd stops. The camera will record three images with different exposures: one exposed
according to camera calculations, one over-exposed and another under-exposed. Over and under
exposure amount is user adjustable. This function helps get correct exposure especially in shooting
moving objects or when environmental lights are complex.
1. Press function button 3 < > and icon
< > and the exposure bracketing amoun will
be highlighted on the LCD panel.
2. Set the flash exposure compensation amount.
•Turn the Select Dial to set the
amount.
•"0.3" means 1/3 step, "0.7" means
2/3 step.
3. Press Set Button again to confirm the setting.
Then your FEC and FEB settings are displayed
on the LCD panel.
-7-
●FEB will be cancelled after three photos are taken.
●For best results, set the camera drive mode to "single" and ensure the flash is
ready before shooting.
●FEB can be used with FEC and FEL.
● You can prevent the FEB from being cancelled automatically after three
photos are taken. (C.Fn-FEB ACL)
FEL: Flash Exposure Lock
FEL can lock the correct flash exposure setting for any part of the scene.
With <ETTL> displayed on the LCD panel, press the camera's <FEL> button. If the camera does not
have the <FEL> button, press the <*> button.
1. Focus the subject.
2. Press the <FEL> button.
•Aim the subject at the center of the viewfinder and
press <FEL> button.
•The camera flash will fire a preflash and the required
flash output fo the subject is retained in memory.
•"FEL" will fisplay on the viewfinder for 0.5s
•The camera flash will fire a preflash and lock the flash
exposure setting once the <FEL> button is pressed.
•Lampa wyzwoli przedbłysk i zablokuje ekspozyję po
naciśnięciu przycisku <FEL>
•If the subject is too far away and underexposure, the < > icon will blink in
the viewfinder. Move closer to the subject and try the FE lock again.
•If <ETTL> is not displayed on the LCD panel, FE lock cannot be set.
•If the subject is too small, FE lock might not be very effective.
High-Speed Sync
High Speed Sync (FP flash) enables the the flash to synchronize with all camera shutter speeds. This
is convenient when you want to use aperture priority fo fill-flash portraits.
1. Press Function Button 2 < > so that < > is
displayed.
2. Check that < > is displayed in the
viewfinder.
●If you set a shutter seed that is the same as or slower than the camera's
maximum flash sync speed,< > will not be displayed in the viewfinder.
●With high-speed sync, the faster the shutter speed, the shorter the effective
flash range.
●To return to normal flash, press < > button again. Then < > will
disappear.
●Multi flash mode cannot be set in high-speed sync mode.
●Over-temperature protection may be activated after 30 consecutive high-
speed sync flashes.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the subject. The flash fires right before
the shutter closes.
Press function button 2 < > button so that < > is displayed on the
LCD panel.
M: Manual Flash
The flash output is adjustable from 1/1 full power to 1/256th power in 1/10th stop increments. To obtain
a correct flash exposure, use a hand-held flash meter to determine the required flash output.
-8-
1. Press <MODE> button so that <M> is displayed.
2. Turn the Select Dial to choose a desired flash
output amount.
3. Press Set Button again to confirm the setting.
Optic S1 Secondary Unit Setting
In M manual flash mode, press <S1/S2> button so that this flash can function as an optic S1
secondary flash with optic sensor. With this function, the flash will fire synchronously when the main
flash fires, the same effect as that by the use of radio triggers. This helps create multiple lighting
effects.
Optic S2 Secondary Unit Setting
Press <S1/S2> button so that this flash can also function as an optic S2 secondary flash with optic
sensor in M manual flash mode. This is useful when cameras have pre-flash function. With this
function, the flash will ignore a single "preflash" from the main flash and will only fire in response to the
second; actual flash from the main unit.
•S1 and S2 optic triggering is only available in M manual flash mode.
Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of
a moving subject in a single photograph.
You can set the firing frequency (number of flashes per sec. Expressed as Hz), the number of flashes
and the flash output.
1. Press <MODE> button so that < > is
displayed.
2. Set the flash frequency and flash times:
•Press the Function Button 2
<Times> to select the flash times.
Turn the Select Dial to set the
number.
•Press the Function Button 3 (Hz>
to select the flash frequency. Turn
the Select Dial to set the number.
3. Turn the Select Dial to choose a desired flash
output. After you finish the setting, press Set
Button and all the settings will be displayed.
Calculating the Shutter Speed.
During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to
calculate the shutter speed and set it with the camera:
Number of Flashes / Flash Frequency = Shutter Speed
For example; if the number of flashes is 10 and the firing frequency is 5Hz, the shutter speed should
be at least 2 seconds.
To avoid overheating and deteriorating the flash head, do not use stroboskopic flash more
than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15
minutes. If You try to Use the Stroboskopic flash more than 10 times in succession, the firing
might stop automatically to protect the flash head. If this happens, allow at least 15 minutes
rest for the camera flash.
•Stroboskopic flash is most efective with a highly reflective subject against a
dark background.
•Using a tripod and a remote control is recommended.
•A flash output of 1/1 and 1/2 cannot be set for stroboscopic flash.
•Stroboscopic flash can be used with "buLb".
•If the number of flashes is displayed as "-", the firing will continue until the
shitter closes or the battery is exhausted. The number of flashes will be limited
as shown by the following table.
-9-
Maximum stroboscopic flashes:
Flash
output/Hz
1 2 3 4 5 6-7 8-9
1/4 8 6 4 3 3 2 2
1/8 14 14 12 10 8 6 5
1/16 30 30 30 20 20 20 10
1/32 60 60 60 50 50 40 30
1/64 90 90 90 80 80 70 60
1/128 100 100 100 100 100 90 80
1/256 100 100 100 100 100 90 80
Flash
output/Hz
10 11 12-14 15-19 20-50 60-199
1/4 2 2 2 2 2 2
1/8 4 4 4 4 4 4
1/16 8 8 8 8 8 8
1/32 20 20 20 18 16 12
1/64 50 40 40 35 30 20
1/128 70 70 60 50 40 40
1/256 70 70 60 50 40 40
Wireless Flash Shooting: Radio (2.4G) Transmission
•When the camera's shooting mode is set to a fully automatic mode or an Image
Zone mode, the operations in thi chapter are not available. Set the camera's
shoothing mode to P/Tv/Av/M/B (Creative Zone Mode).
•The STROBOSS 60 II attach to the camera is called the transmitter unit, and a
STROBOSS 60 II that is wirelessly controlled is called the receiver unit.
•You can also wirelessly control the STROBOSS 60 II set as the receiver unit
with the transmitter Quadralite Navigator X (sold separately). For details on
setting the transmitter unit functions, see the transmitter's instructions.
Using a flash (transmitter/receiver) with a radio transmission wireless shooting function make it easy to
shoot with advanced wireless multiple flash lighting, in the same way as E-TTL II autoflash shooting.
The basic relative position and operation range are as shown in the picture. You can ther perform
wireless E-TTL II autoflash shooting just by setting the transmitter unit to <ETTL>.
Positioning and Operation Range (Example of wireless flash shooting)
•Autoflash Shooting with One Receiver Unit
•Use the supplied mini stand to position the Receiver unit.
•Before shooting, perform a test flash and test shooting.
•The transmission distance might be shorter depending on the conditions such
as positioning of Receiver units, the surrounding environment and whether
conditions.
Wirelless Multiple Flash Shooting
You can divide the Receiver units into two or three groups and perform E-TTL II autoflash while
changing the flash ratio (factor). In addition, you can set and shoot with a different flash mode for each
firing group, for up to 3 groups.
Auto Shooting with Two Receiver Groups
-10-
Auto Shooting with Three Receiver Groups
Shooting with a Different Flash Mode set for Each Group
* The flash mode settings are indicated only as an example
Wireless Setings.
You can switch between normal flash and wireless flash. For normal flash shooting be sure to set the
wireless setting to OFF.
Transmitter Unit Setting
Press < > button so that < > is displayed on the LCD panel.
Receiver Unit Setting
Press < > button so that < > or
< > will displayed on the LCD panel.
Transmitter Unit's Flash OFF
When the Transmitter unit is set to OFF, only the Receiver units will fire a flash.
1. Press <MENU> Button to enter C.Fn
Transmitter settings.
2. Set Transmitter to ON/OFF to control the
On/Off of the Transmitter unit
< > The Transmitter unit flash firing is ON.
< > The Transmitter unit flash firing is OFF.
•Even if the Transmitter unit flash
firing is disabled, it still fires a
preflash to transmit wireless
signals.
Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the channel Ifs to prevent signal
interference. The channel ID's of the Transmitter unit and the Receiver unit(s) must be set to the same.
-11-

Najnowsze poradniki

Zobacz więcej
depilator laserowy ranking

Ranking depilatorów laserowych - najlepsze depilatory laserowe

karma dla kota junior

Ranking najlepszych mokrych karm dla kota junior

najlepsza karma dla kota

Ranking karm dla kotów - najlepsze karmy dla kotów

rozmiary telewizorów

Rozmiary telewizorów – przeliczenie cm na cale

jakie zabawki dla noworodka

Jakie zabawki dla noworodka wybrać?

temperatura w lodówce

Jaka temperatura w lodówce jest odpowiednia dla produktów?

jak działa kompresor

Jak działa kompresor w samochodzie?

data premiery GTA 6

GTA VI miało zadebiutować dużo wcześniej? Szef Take-Two zdradza powody opóźnień największej gry dekady

historia roweru

Historia roweru – kiedy wynaleziono rower?

najlepsza patelnia żeliwna

Najlepsze patelnie żeliwne - ranking patelni żeliwnych

czytnik ebook ranking

Ranking czytników e-booków - najlepsze czytniki e-booków

najlepsza walizka kabinowa

Najlepsze walizki kabinowe - ranking walizek kabinowych

biografia

Najlepsze biografie - ranking książek biograficznych

smartwatch do pływania

Najlepszy smartwatch do pływania - ranking smartwatchy wodoodpornych

recenzja Media Expert gry Forza Horizon 6

Forza Horizon 6 – recenzja. Drift pod kwitnącą sakurą

Sprawdź więcej poradników

Pobierz aplikację mobilną Media Expert

Pobierz z Google Play
Pobierz z App Store

Właściciel serwisu: TERG S.A. Ul. Za Dworcem 1D, 77-400 Złotów; Spółka wpisana do Krajowego Rejestru Sądowego w Sądzie Rejonowym w Poznań-Nowe Miasto i Wilda w Poznaniu, IX Wydział Gospodarczy Krajowego Rejestru Sądowego pod nr KRS 0000427063, Kapitał zakładowy: 41 687 500,00 zł; NIP 767-10-04-218, REGON 570217011; numer rejestrowy BDO: 000135672. Sprzedaż dla firm (B2B): dlabiznesu@me.pl INFOLINIA: 756 756 756